Search:

Type: Posts; User: Cantechman

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    588

    [Error Code] Re: Bizhub C300i D073 error

    Have you tried to see if you can format it? Maybe you could change it after trying that. I have no other ideas on what to try there, I hope this is a charge call.
  2. Replies
    11
    Views
    1,239

    Re: Brand new C450i with 3205 jam code

    May or may not help but i just fixed a 3003 jam code on a c300i where it would stop every time as it was passing thru the fuser. The issue was with the baseboard. Once replaced it was fine. I had...
  3. Replies
    7
    Views
    939

    [Misc] Re: Konica C450i Intermittent Paper Empty

    Not exactly related but i had an issue where paper would just feed out pass the feed rollers of tray 1 and stop every time, replacing the whole paper feed assy fixed it, i was told by tech support to...
  4. Replies
    10
    Views
    1,739

    [Misc] Re: Konica Minolta BizHub C300i

    I would imagine if the waster toner box is installed properly then it must be a bad sensor, Waste toner box set sensor (PS46) or the board or cable.
  5. Replies
    13
    Views
    1,313

    [Misc] Re: Konica minolta c284 unsolvable problem

    So you come on a site where technicians help others and while asking for help you say there are no good technicians anymore? That's a great way to ask for help.
  6. Replies
    20
    Views
    1,537

    Re: Konica C253 - colors do not match

    That's a dinosaur these days, I would also look at the 2nd image transfer roller, there a lot of possible issues, I would definately do as the others said as well.
  7. Replies
    10
    Views
    1,044

    Re: C558 copy quality

    Replace the 2nd image transfer roller, I have had that problem in the past and that corrected it.
  8. Thread: Vcare Woes

    by Cantechman
    Replies
    8
    Views
    652

    Re: Vcare Woes

    Have you checked the port number in vcare in the server settings? I normally have to change it manually to 80, do a ram clear and data initilization. It works after that.
  9. Replies
    31
    Views
    394,505

    Re: C250i No yellow on rear side of page

    Do you have a picture of where that part is? it would be good to know for future reference.
  10. Re: New c550i intermittent dog ear non op side lead edge of paper

    There has been issues with the mylars the paper makes contact with as it leaves the tray. Maybe that's worth a look?
  11. Replies
    31
    Views
    394,505

    Re: C250i No yellow on rear side of page

    Have you tested the toner supply motor for yellow?
  12. Replies
    9
    Views
    1,112

    [Misc] Re: bizhub 454e blank prints

    I would try the HV board after checking the various % levels and doing a self check in service mode on the boards.
  13. Replies
    9
    Views
    1,112

    [Misc] Re: bizhub 454e blank prints

    Is it completely blank or is there some shade on the prints? i would reseat the transfer belt and transfer roller first. I had that issue with a light gray showing up on prints and it was the HV...
  14. Replies
    6
    Views
    966

    Re: C1060 warming up after fuser rebuild.

    I had that issue once, could not figure it out. Only a new fuser fixed it.
  15. Replies
    9
    Views
    2,399

    Re: i series toner backup

    I had the 2204 error on a c450i today, it was making a noise. There was no buildup of toner, once i reinstalled it the error and noise went away. Should I still cut a few of the coils off the...
  16. Replies
    8
    Views
    788

    Re: Am I getting old........ or... WHAT?

    As I was reading your message i was thinking it must be those rollers as I have seen that in the past as well, then I read that it actually was lol.
  17. Re: c554e startup and job receiving problems

    Does it have any errors on the counter in service mode? I would suspect a failing HD even though it tested ok. There should be some type of errors listed if it's not booting fully.
  18. Thread: Biz 4750

    by Cantechman
    Replies
    3
    Views
    344

    Re: Biz 4750

    Were they using the previous vendor's email service? By updating do you mean they are still with the same company? Maybe there's a setting in the new router blocking it if there is a new one.
  19. Replies
    7
    Views
    707

    Re: FS-539 eject claw

    I'm not trying to highjack your post, but is there an actual written procedure anywhere to remove that ejector unit? I i may have to replace that same part on a FS-537 and it seems to be impossible...
  20. Replies
    9
    Views
    1,733

    [Electrical] Re: C250i Won't Power On

    Sounds silly but i would check that the correct power is coming from the plugin. Is it plugged into a EPS surge protector? if so just try it without it. I have seen those go bad before.
  21. Replies
    22
    Views
    2,067

    Re: Konica Minolta C368 P-22

    I would try the FSB. Since the IDC sensors connect to it (if i'm not mistaken) and since you already replaced the sensors I would look there.

    I would also make sure the IDC sensor shuttle is...
  22. Replies
    3
    Views
    664

    Re: BH-C-284e, two issues

    If you log into service mode and check the counters you should be able to see the error code there under one of the categories. I had the same model give the internal error message, it would try...
  23. Re: Konica Minolta bizhub 601 - Light stain on the entire sheet

    if you can find one I would replace the dev unit.
  24. Re: [Image Quality] Thin line won't go away on Konica bizhub Press C6000

    Have a look to see if there is some sort of fiber, hair or dirt that is blocking the image from getting to the drum. Look in between the gap between the dev unit and drum on the transfer unit side....
  25. Replies
    10
    Views
    4,404

    [Error Code] Re: Bizhub C3850 Error Code 6790

    Well then it's not the belt if it's moving unless it has missing teeth or something which is something I have never seen happen.
Results 1 to 25 of 209
Page 1 of 9 1 2 3 4