Have had this prob once before.you mau laugh but have u tried changing the cat5 cable or a new port?I was going to suggest reloading to new firmware which is build 9,but you cant see it off the...
Type: Posts; User: kmking
Have had this prob once before.you mau laugh but have u tried changing the cat5 cable or a new port?I was going to suggest reloading to new firmware which is build 9,but you cant see it off the...
Hey Buddy,
I have had this problem once before(one of our techs) and it was mechanical.it was a drive gear,have a look around the drive system.give me a couple of days and I will let you know...
Thankx for all your help fellow techy's,one of our guys had a brass washer on the end of the transfer belt rather than an insulated washer.One one end it was an insulated washer,but on the other end...
Yep Jam 60 and jam "62" are the commpm jams in the duplex area.Have found the solenoid in the duplex area for the paper conveying section needs a good clean out from time to time.Rust develops in the...
Have replaced the who;e tranfer assembly complete.ie the whole tray unit(fuser ,cleaning brush)etc,from another 7530,and still no result,same thing.still scratching my head,ta BSM2
Hey guys out there,I have a KM7530,where the txfer belt is fully coated with toner(permanantly)I have cheanged the board under the txfer belt,hv board,drum potential sensor,tx cleaning brush,but not...
Hey Guys.
Got a KM 7530,the txfer belt is covered by toner permanantly.Have change,dev bias board,hv PCB,main Board,the whole transfer assembly,xfer cleaning sysytem,drum potential sensor,the only...
Kyocera have put a mod out for this problem.They have modified the exit unit.it now has upper and lower sep claws on it.I have put many of these in and the problem is gone.Takes about 30mins to put...
Hey there buddy,If you take the rear cover off the back of the machine it will have the simulation codes in there ,plus the default values of what the machine is set at.Hope this helps.
Kyo's all the way ,Here in Australia...Hey Sakis...Your in Greece...well well well.giasou patrioti....
PM kit has been put in.It only happens in the morning on start up...after a few attempts of switching on and off it will go on and on without fail...untill the next morning.but i think i have nutted...
Hi guys,has any body out there has had an error code of
C2550?on the service manual it says its a main motor problem and i have replaced it..could it be some sort of TORQUE being applied to the...
I am in Australia we sold alot of these machines.If you take off the rear cover you should see the simulation chart...hope that helps..
Hi there fellow techy.
I do have a print system(Q) brand new in the box and a scan system (D),Brand new in the box aswell.The only problem is that I am in Sysdney Australia,I also dont know what...
There is a firmware update to counteract the slowness of the panel
The km-4850 is a dream machine,As long as you keep the firmware up to date,as there are issues with acrobat 7.0 and above.I have found version 3.3_009 takes care of these issues.As for the new...
As you are looking at the rear side of the machine you have 2 sensors,an upper lift sensor and a lower sensor for when the tray is in home position,either up or down.I have had this error code before...
These machines are great.The only issues that I am aware of is that the Drum drive mtrs can sieze up and throw u up an error code.Also plse note when taking out the feed assembly situated at the rear...
Well.. havenet heard of ant problems.but then again we have justr only released them here in AUS only a week ago..no real feed back as yet.But the color reproduction is very good..beats the crap out...
Never use Katun toner...It destroys the lower drum seal..and u will lose copy quality..the amount of Silicon in the toner is not very high..therefore causing the drum seal to erode away..pay that...
I ave 9 of these machines in the field..7 of these havent given me any problems...I have visited 5 of these machines twice in 500k copies..not a bad track record..but wait there's more..wait for the...