Search:

Type: Posts; User: joelsa12

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: ROM Check

    by joelsa12
    Replies
    1
    Views
    503

    ROM Check

    So in the past on the older Sharps I was able to go into management mode and check if the three system ROMs matched. I believe that a tech has one switched. I for the life of me can not remember...
  2. Replies
    11
    Views
    2,977

    Re: RC6300 paper jam, no paper jam found

    just a stab in the dark here. but the machine is not seeing the paper come out of the machine, but it thinks that one has fed in. which style stripper unit it is in the machine? is the stripper...
  3. Re: Help! Ink smearing question GR 3750 Risograph

    nope i do not. i live in indianapolis..... if i am ever up that way i will hit you up.
  4. Replies
    8
    Views
    2,201

    [Misc] Re: GR3770 inks drying method

    riso inks have always dried by being absorbed. i beleave the word is imulsification. i bet i murdered that spelling. if your paper is too glossy it will not dry.....ever
  5. Re: Help! Ink smearing question GR 3750 Risograph

    so many issues...... so many adjustments...... if you get a hold of the service manual there are many adjustments to cut back the ink. a properly adjusted machine printing on the proper paper(not...
  6. Replies
    3
    Views
    1,716

    Re: RISOGRAPH GR3750

    there is a long process that you can go through to adjust the 0-180 magnet, but if you just make it look like a working drum then you should be fine. at the end of the drum that goes into the...
  7. Replies
    6
    Views
    2,672

    Re: Sharp MX-511N Custom Print Size

    I kind of have the same issue going on. How did you get the 9X12 envelope to print with out wrinkles? In my case there is always wrinkles. If I tell the machine that there is COM 10 envelope in...
  8. Replies
    5
    Views
    7,966

    [Error Code] if the bearing is going out there will be an...

    if the bearing is going out there will be an audible noise coming from the transport section. there are three rubber belts that transport the paper out of the machine. under the rubber belts on the...
  9. Replies
    5
    Views
    7,966

    [Error Code] the problem is with the ejection part of the...

    the problem is with the ejection part of the machine. the motor that drives the belts that paper come out on is where the error is pointing. i have found that the bearing that support the shaft...
  10. Replies
    15
    Views
    6,350

    one other thing i am always thinking of more...

    one other thing i am always thinking of more stuff after i post. do you still have the 5.5 mm screw that holds in the magnet?
  11. Replies
    15
    Views
    6,350

    I have many of them!!!! PM me your address and I...

    I have many of them!!!! PM me your address and I will send you one. It should fit in a plain envelope. In the mean time if you have any other RA or GR drums sitting around you can take it off one...
  12. Replies
    15
    Views
    6,350

    ps it is a very stong magnet and would have stuck...

    ps it is a very stong magnet and would have stuck to anything metal that was close to it. metal desk maybe???
  13. Replies
    15
    Views
    6,350

    The magnet is on the back of the drum attached to...

    The magnet is on the back of the drum attached to the clamp on the drum. Its job is to tell the machine if the clamp on the drum is open or closed.
  14. Thread: faxes stuck

    by joelsa12
    Replies
    19
    Views
    3,968

    just a shot in the dark here, but I have had lots...

    just a shot in the dark here, but I have had lots of faxing issues with people what have digital phone lines. faxing and the new VOIP systems does not like each other at all. I would ask them if...
  15. Replies
    5
    Views
    1,624

    Could the machine be loading the master a little...

    Could the machine be loading the master a little crooked? If all is good with the paper feed and timing that is where I would look next.
  16. Thread: gr3770 slide

    by joelsa12
    Replies
    10
    Views
    2,220

    was that me making your day? if so glad i could...

    was that me making your day? if so glad i could help.
  17. Thread: gr3770 slide

    by joelsa12
    Replies
    10
    Views
    2,220

    third have your left hand clicking the drum set...

    third have your left hand clicking the drum set switch, push the green button with your right hand and quickly move your right hand to the power switch. you will be watching the drum chuck in the...
  18. Pull out the drum. Find pressure roller. Look to...

    Pull out the drum. Find pressure roller. Look to the left. You should see the next set of rollers. This is timing and guide rollers follow to the front frame where the rollers come through the frame....
  19. Replies
    5
    Views
    2,308

    all i can think of is this. is the top disposal...

    all i can think of is this. is the top disposal roller fastened down? i remember the little clips on those things not always staying on. how is the clamp on the drum that you are using? there are...
  20. Replies
    5
    Views
    2,308

    there is a one way gear that goes out in the...

    there is a one way gear that goes out in the disposal unit. are the disposal rollers rolling? or are they just sitting there? pull the d unit and check it and make sure the motor is turning the...
  21. [Misc] well there is a pressure lever i believe that it...

    well there is a pressure lever i believe that it is call press. lever B. it can be slightly bent( the naked eye can not see it) and it will cause the press roller not to lock back into the down...
  22. Replies
    5
    Views
    1,481

    [Electrical] adjust the stack switch in the paper feed unit. ...

    adjust the stack switch in the paper feed unit. it is behind the green dials where you put the paper in. It will cut power to the clutch.
  23. [Misc] I have yet to see a solenoid go out on the RP...

    I have yet to see a solenoid go out on the RP series there is a pressure lever that gets bent and will cause your issue. I do not think that an end user will be able to replace this lever and get...
  24. Thread: RISO RC6300

    by joelsa12
    Replies
    5
    Views
    1,496

    [Error Code] take a piece of paper and fold it in half. take...

    take a piece of paper and fold it in half. take the folded edge and push it through like you were loading a master. sometimes the cut master strip will get stuck in there. Old style master sensors...
  25. on the 3770 adjust the parallelism of the timing...

    on the 3770 adjust the parallelism of the timing and guide rollers. on the 6300 the pastic strips with the metal in the middle are getting in the way as you master is loading. they are non...
Results 1 to 25 of 265
Page 1 of 11 1 2 3 4