Hi Guys,
I'm about to purchase a Konica Minolta Bizhub Pro 1051 with a GP-501 (Made by GBC) - The unit only came with a three-hole punch die set installed, but it looks like it has three empty...
Type: Posts; User: langelot
Hi Guys,
I'm about to purchase a Konica Minolta Bizhub Pro 1051 with a GP-501 (Made by GBC) - The unit only came with a three-hole punch die set installed, but it looks like it has three empty...
Hi all, I am looking for a punch die for this punch unit - it goes on a variety of Konica Minolta Machine (Bizhub Pro 1200 - C6500 - Bizhub Pro 951) - the KM designation for this machine is a DS-512...
Thanks Darren King - that makes sense!
The problem is that what I really need to do is to install the Océ Firmware for the PPLM (Proactive Part Lifecycle Management) - a fancy term for changing...
The slots where the toner cartridges goes into and locks into are also different. I had to break a few tabs on the konica cartridge to get it to fit the Océ, only to see that the machine didn't...
[Does anyone know if the Oce CM 3522 (KM C353) uses a special oce firmware or is it the same standard KM software. Will it accept the KM firmware and if it will, will it cause issues?
Hi there,
I have a customer with one of these envelope presses - great machine apparently. Recently though, when came time change the cyan toner, an employee mistakenly put a black unit instead,...
I might be interested in the supplies if you still have them and are well priced.
I'm looking for the same thing, and toner, drums & developer as well - any luck finding a good supplier?
Hi, hoping you might still have some supplies (Drums, Developers, PM kits or Toner) for the 8050.
No... the machine is not hooked up - we don't have the necessary amperage on our 220V line to run the machine. It was pulled from our account in lieu of payment and the machine was printing and in...
Hi guys, I have two working print controllers for the 7075's an IP-601 and an IP-601M. They are used but in good working condition. Make sure that your machine(s) have the video interface kit...
We have all the items - I am out of South Florida - where are you located?
We have a Canon Image Runner 150 that we are looking to sell and are hoping that someone here might have an interest. We no longer have the manuals, but here is the information we have based on the...
We have between 25 to 30 LCT's for the Konica Minolta brand.
Since there is no demand for them for export we have shipped out our machines without LCT's. . We are located in South Florida. I'll...
Hi everyone, I have a friend in New Jersey who is in need of a folding finisher for the Bizhub 600 - that model would be the FS-602.
If that is unavailable, we could use either a FS-210 or a...
Someone must have one of these they would like to sell! - bump -
Everything is pointing to the HV Power Supply 2 (the power supply for the transfer/sep. unit) or the transfer/sep. unit itself. My reccomendation: first the code is pointing to the separation and...
Hi all,
I've bought and worked on a few of these in the past few years and only now do I think that the Fiery print controller on the Di-850 (Minolta) is probably superior on this engine than the...
I have seen this type problems on several occasions - one as mentioned above had to do with worn/out of place magnets within the developer sleeve - but this is unlikely because of 700k doesn't make...
Ok - Here's the full list of the different guises of the Konica 7085 - I would be willing to buy several of these.
Konica 7085
Konica Force 85 (Printer Only - No Doc. Feeder)
Minolta Di-850...
Hi everyone,
I am looking for this model in any of its many guises or even better for a bizhub Pro 920.
I know these machines quite well and would only consider one that is competively...
I might be interested in the Konica 7085 - would you sell it separately?
When doing the 47-93 you've reset a few dip-switches, including the one that controls the full-auto screen to the factory defaults. Anyhow, go to 25 mode (same way you accessed 47 mode) pressing 2 &...
Its IEEE1394 cable better known as a firewire cable with the six circuit male connectors at both ends (important) - this was probably the original version of that cable - you can easily get it at a...
Willing to pay $1,500.00 US - Anyone? Ayone?