Image registration is correct on 1st page. Subsequent pages image is off about 1/2 inch. (image is moved down page) does it from all trays. Cleaned reg roller. CLutch looks impenetrable. Machine...
Type: Posts; User: Deer John
Image registration is correct on 1st page. Subsequent pages image is off about 1/2 inch. (image is moved down page) does it from all trays. Cleaned reg roller. CLutch looks impenetrable. Machine...
We are primarily a Sharp dealer. Have a few of these at a Gov't account. One of them has a noise and then this error. Apparently Laser Unit has failed. I'm currently locating one. Are there any traps...
This machine does this for 12-20 seconds from even a 30 second standby period...if you continue to make copies subsequently without stopping it does not do it. Driving my customer and by extension,...
I have this machine at a very fussy account and they are complaining that the machine gives this message and makes them wait 15 seconds or so most every time they use is from standby.
I can't find...
The lead edge of copies from tray 1 is off (late) by about 1/2 inch.
I have tried the adjustments in the svc programs including paper buckle to no avail. It does it thru the SPF as well as on glass....
This 3510 jams at feed out of all 4 paper drawers. Press print, machine cycles and the timing (no matter which drawer is selected) sounds like it is about to feed, calls jam. Paper never left drawer....
This 310 is otherwise fine. It goes thru the motions of receiving a fax and prints a blank page. It transmits faxes fine but won't print the transmit confirmation report at all. Updating firmware...
Have a crazy rich customer who loves these machines. I have been keeping his running for 15 years and am now out of options for parts for them. Anyone have one stuck back in a warehouse somewhere I...
Bizarre....This networked MFP randomly delivers jobs, (sometime in the middle of one) to the top tray in reverse order. As if an invertor solenoid or gate was sticking open. Began when another...
This machine randomly delivers printed and copied sets into the top tray in reverse order (face up) doesn't jam. Seen this?
Replaced the fan this code apparently refers to...warmed up, went ready, passed one copy, coded out 490 aagain. AM I on the right track...anything else cause this code?
Know this is a fan code. They all seem to be working. No fan noises, clogged filters etc. Which fan is it usually?
Know this is a fan code. They all seem to be working. No fan noises, clogged filters etc. Which fan is it usually?
First saw this machine for "finisher front door open". Switch was good ...had Hy-tec repair finisher main board. Finisher is MX-FN9. Has hole punch unit. After PWB replacement, machine booted up fine...
Took in a Savin 8035 on trade that is too clean to dump on a wholesaler. I need to get it to network scan on Windows Vista and 7. Do I need scan software loaded on the client computers? Could someone...
Machine displays "waste toner bottle full" and my technician cant find it...where is it and does replacing it reset the message?
Codes out, will not reset. I know that this is an exhaust fan error code, but am unsure where it is located. Does anyone have a rough location or parts number for the exhaust fan or fans related to...
Customer has a Kip 3000 that goes thru the motions of warming up. Fans, motors, stuff turning but no display. Would be leaning toward bad display but when they try to print to it they get message...
Have a 5030 in the field that has been happy until recently displaying the following message"
A software compatibility problem has been detected, a software upgrade is required, please use the...
Have a 500 that codes out at powerup with this finisher code. Remove finisher runs fine. No obvious mechanical /electrical problems with finisher. What usually causes this code? Manual did'nt help...
Know this is a toner waste pipe backed up code. Removed waste toner bottle and stuck a screwdriver up there to free packed toner. Still codes. What next and what is the sim to cycle this system?. TIA...