Are they using custom paper catalog entries for this media?
If so, check the custom settings for the slower machine, and look for a field called Process Speed Setting. If it's been set to...
Type: Posts; User: Rorschach
Are they using custom paper catalog entries for this media?
If so, check the custom settings for the slower machine, and look for a field called Process Speed Setting. If it's been set to...
When you say assembly, do you mean the corona itself?
I might lean towards a wonky power supply. PSU3 is the one that the corona cleaning motors get their 24V from via IOB1. I don't think there's...
If you've done the boards and some harnesses, check the feed and transport motors as well as the pick-up and inverter solenoids. That, or perhaps one of the harnesses you didn't do yet is shorted.
In addition to the belt and 4 image transfer (D0746158) rollers that you've already changed, I would suggest the opposed roller (D0746110) as well. This is the ITB bias roller at the very bottom of...
It's a setting in the paper catalog. IIRC, the ones to change are around 67 and 68, but don't hold me to that. I can't check this week, because I'm traveling, but I can check on Monday. I think it...
Looks like it's probably caused by the PTR bias being too high for the trail edge. You need to change the bias settings in SP modes for whichever paper setting you're using.
SP2428-001 through...
Take a look at the sensor feeler (D7772752) that passes through the photointerruptors on the left side of the tray as it lifts/lowers, as well as the sensors themselves. I had one on a C9110 last...
The Pro C901+ Graphics Arts edition will handle 350gsm through the A3/DLT LCT only. The A4/LT LCT can only handle 216gsm from trays 3&4 and 163gsm from tray 5. Trays 1&2 in the mainframe can only...
I've seen the new Ricoh Mimaki flatbeds print on sheet metal and a door. Pretty amazing to watch that in action.
Among the color production machines, the Pro C901+ will handle up to 350gsm through the LCT, the Pro C71xx will handle up to 360gsm through the vacuum feed LCT, and the Pro C91xx will handle up to...
Too funny. I'll have to give this to me friends on the low-volume team. :-)
And FWIW, the color production models are named after constellations. The C651/751 was the Taurus, the C7100 is the Leo,...
Out of curiosity, has the machine logged any SC codes other than the SC569? There's something in the knowledge base about the relay board causing problems that may lead to a fiery disconnect.
Have...
Which Fiery do you have attached to the C900? They typically come with the Fiery controller that mounts inside the rear box on the mainframe. But they were also available with the E-80, which is an...
What sort of wear are you seeing? Can you post a photo of it, so we can get a good look at what exactly you're talking about?
You mention that you see this wear cause image quality issues on cover...
As Slimslob mentions, the MP C6502/8002 has a maximum feedable paper size of 13x19.2 per the product support guide. The maximum image size on these boxes is 12.71x18.9.
Other than the D135/D136,...
It appears that you've got the service manual in hand, since you mentioned a paper reset, and EEPROM reset.
First, I'd try setting it up for 11x17 as a custom size. Sometimes these Plocks give...
True, but the OP only said that they tried installing a DF that worked fine on another machine, so it wasn't really clear that the problem machine had the correct BCU, only that he had changed the...
Yeah, you're right. The firmware is resident in the doc feeder. It's been so long since I've turned a screwdriver on a box with a DF, it slipped my mind.
However, the parts catalog shows the...
Which IPU did you order and put in? If the mainframe originally had an ARDF, then it likely came with the IPU made for that doc feeder. If you replaced it with the same part number and are trying the...
I've almost always found this caused by a thin sheen of condensation on the black drum. Usually during the summer when an A/C vent above the MPF blows cold air near the vent on the right side of the...
What barratec said. Resetting the web PM counter via SP7804-005 usually does the trick for me.
Per the specs given in the FSD, you can run the following paper weights:
Trays 1 and 2
52.3 – 216 g/m2
14 Bond – 80 lb Cover
Tray 3
52.3 – 256 g/m2
14 Bond – 90 lb Cover...
The bushings only come with the transfer roller (B262 3802). They can't be ordered separately.
As far as I know, the print/scan SD card is an accessory item, not a part.
Printer/Scanner Unit Type 2105, EDP code 411256.
Also, you need to have an additional 256MB stick when installing the...
I assume you're putting the AE030047 bearings on with the collar to the inside of the UHR? It's a nifty little fix, and one I plan to put to use when I come across one of these buggers; I hate...