Now I have set the falling position on sorter. It is a little bit more than 2 mm. The test run worked well, hope it works well for the customer also now.
Thanks
(It gets a little strange with...
Type: Posts; User: DIMM
Now I have set the falling position on sorter. It is a little bit more than 2 mm. The test run worked well, hope it works well for the customer also now.
Thanks
(It gets a little strange with...
When stapling - first sheet in a staple, is pulled out of position in the top tray, when the booklet beforey is ejected to the tray.
This does not happen all the time but too often, and sometimes...
A little late to answer, but your tips helped. Blow out the fans, and everything clean from dust. Now, the LED is green again.
But a capacitor on the motherboard was broken and another about to...
It was the status light that glows yellow with black display, on the customers imagePASS-S2 external print controller. Misunderstanding between me and the customer, when he called and reported the...
Hi
Anyone have experience with this problem. No troubleshooting or rebooting of the device yet, because printing works without problems.
The display has sometimes flashed yellow a few times...
I have the exact same problem with one IR7086 and have mounted a new AP Assembly and fuser mm. After about 6k double-sided problem is back again.
Was it a gear on Cleaner Drive Assembly, the damaged...
Dcon clear is done and we'll check for bad ground,
while we wait for the ordered fixing drive assy.
I've already tried replacing fixing unit FM4-6228 (Sweden 230 V)
and more with no results, and have ordered fixing drive assy FM0-1158.
for the next action to resolve the error.
But maybe it's a...
Did you find out what the error code was caused by?
I have a printer with the same error code E009.
It rattles in the printer every morning they start it,
some mornings the error code came and...
Sata Flash PCB is the faulty card, but will take time to fix,
since it can not be fast moved from another c2020i.
Rarely wrong on new cards, so why this time!
"connection cable" do you mean a specific cable? We have tried to check most of them around the cards.
SDRAM's, DIMM ASS'Y, AC DRIVER PCB ASSEMBLY and HDD tested today from identical C2020i...
I'll check them again today. The error started when a scan to folder froze for the customer.
yes, as a set.
It sounds like the printer starts up everything really, except the errorCode
Now I have changed both FM4-3139 Main Controller 1 and
FM4-3143 Sata Flash PCB, but the error code E614-4000 is
still in the printer display at startup.
No success yet.
At startupt the error...
Thanks. New DIMM fixed the problem. :)
S/N:JPBT89HGBT. 69200 prints
(Powering on the printer, no display is visible)
The printer will not start up, it appears only a white Error Code box on a black screen with text E614-4000.
Someone who has experienced or knows anything about this error?
With best regards
It was the FC7-6068 Bushing on right side of FC7-6107 Roller, Reverse
that was gone. Have not found even a few pieces of the bushing.
Have ordered a new one now.
Constant Jam 0210, always stop before the fix, but no error codes.
Three papers, the last down at the transfer belt roller.
Thanks in advance.
The powder CHOROX A-31 (mix), was very good for a worn drum.
The white line was from the dust proof glass.
(The old technician who was my supervisor told me that it was a diode. And I have...
Here is the PG7, PG4 was perfect white, the WDM=370.
I cleaned ca 10 mm of the drum surface in both ends from toner debris, that rotate against the yellow rollers. And that was the solution...
This means the drum is 2000K over its approximate lifetime now.
We had a publishing company as a customer. But it was impossible to set the series iR2200 to 3300 in their building.
We believe it was something electrical breakdown when they started the presses at...
Thanks for your replies
This machine gives me a headache. I have replaced all three Coronas,
and developer. Will clean the laser and drum unit section tomorrow.
This printer has printed out...
I have tried to change the Main Charge Corona again without success. The whitestripe across the botton of the page has been there a few weeks. But beyond their main printing area.
Can laser device...
Hello!
I have a problem with a Canon ir7086 with stripes when printing a "PG6" (see the attached pdf).
Have changed developing assy and all corna assy.
Can anyone help me solve this problem?...