Search:

Type: Posts; User: Koosie

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: DX3243 Jamming

    by Koosie
    Replies
    0
    Views
    350

    [Jamming] DX3243 Jamming

    Hi all,

    I have an issue with a DX3243 Jamming at the registration roller. It doesn't happen every time, but about every 2 to 10th time. The paper is fed to the registration roller, but the...
  2. Thread: Paper format

    by Koosie
    Replies
    2
    Views
    583

    You didn't specify what machine you are using....

    You didn't specify what machine you are using. Just make a copy and test it. It will most likely work.
  3. Replies
    16
    Views
    2,301

    I can definitely swap the 2 trays on all my...

    I can definitely swap the 2 trays on all my 220's. Maybe a Savin thing?
  4. Replies
    16
    Views
    2,301

    I have swapped the trays of an AF220 just last...

    I have swapped the trays of an AF220 just last week. Maybe our models are different from yours.
  5. Thread: Transfer Belts

    by Koosie
    Replies
    6
    Views
    1,006

    I think they are talking about a Ricoh. Maybe...

    I think they are talking about a Ricoh. Maybe Savin.
  6. Replies
    16
    Views
    2,301

    What happens if you swap tray 1 + 2 around?

    What happens if you swap tray 1 + 2 around?
  7. Replies
    16
    Views
    1,960

    What's the error codes? SP5-993-7

    What's the error codes? SP5-993-7
  8. Replies
    16
    Views
    1,960

    Sorry, I forgot to tell you that you can try the...

    Sorry, I forgot to tell you that you can try the forced alignment, but it will not work if the lines are to far part. Try to adjust the lines with SP2-909 and 2-916. Its difficult, but if you get the...
  9. Replies
    16
    Views
    1,960

    Set SP5-993, Line Position Adjustment, 10 through...

    Set SP5-993, Line Position Adjustment, 10 through 21 to the Factory Data Sheet. If you don't have the Factory Data Sheet, Set them all to 0. Don't adjust these settings until the Forced line position...
  10. Sometimes the chip on the toner bottle is not...

    Sometimes the chip on the toner bottle is not working and the machine still thinks the toner is empty. Replace the toner.
  11. Thread: Wipe your

    by Koosie
    Replies
    9
    Views
    1,264

    Don't give it to a customer!!!!! They'll try to...

    Don't give it to a customer!!!!! They'll try to put it through the bypass!!!
  12. Don't laugh at stupid people! I have seen a lot...

    Don't laugh at stupid people!
    I have seen a lot of customers that don't know how to operate the machine because they weren't properly trained on the machines. And some of them are smart people.
  13. Replies
    13
    Views
    2,336

    Open the laser unit and clean the small...

    Open the laser unit and clean the small rectangular glass next to the laser diode. It's the first thing the laser goes through. I have seen a lot of them that is dirty. BEFORE YOU REMOVE THAT GLASS,...
  14. Replies
    10
    Views
    2,143

    Problem solved (for now). The yellow plastic bit...

    Problem solved (for now). The yellow plastic bit had a thin film of plastic covering it, witch I removed, revealing a sticky surface beneath. That seems to solve the problem.
  15. The drum can be disassembled easily, but usually...

    The drum can be disassembled easily, but usually cleaning the drum units is only a temporary solution and the problem will reappear.

    Always use genuine toners in color machines!!!
  16. Replies
    11
    Views
    2,509

    Also, clean the ID sensors. They are behind the...

    Also, clean the ID sensors. They are behind the fusing unit. Do not adjust any SP's in 5-993, this will cause the line position to be altered after a 'Line Position Adjustment' has succeeded. Return...
  17. Replies
    19
    Views
    2,640

    Inform us when you solved the problem. It's...

    Inform us when you solved the problem. It's probably a board. Check the door switches. I'll replace the BICU first. (won't take longer than 44 minutes to replace :) )
  18. Replies
    19
    Views
    2,640

    Check the cable running from the fusing unit to...

    Check the cable running from the fusing unit to the power supply for continuity, maybe a broken cable?

    Blowing up the machine will solve the SC-542 issue, but the customer will still not be able...
  19. Replies
    10
    Views
    2,143

    I will be adjusting the springs under the...

    I will be adjusting the springs under the seperation pad, and maybe covering the sep. pad with some tape for more grip. Will inform you of any success.
  20. Replies
    10
    Views
    2,143

    I will replace the rollers if one of my McGyver...

    I will replace the rollers if one of my McGyver moves don't work. (I don't have stock)

    Thanks.
  21. Replies
    10
    Views
    2,143

    Yes, the pad and the cover beneath is still...

    Yes, the pad and the cover beneath is still spring loaded. I will try to adjust the pressure.

    I did blame the paper and the amount of paper they put in the machine. I told them they shouldn't load...
  22. Replies
    10
    Views
    2,143

    Yes, that plastic is still there. It is a bit...

    Yes, that plastic is still there. It is a bit yellow. Should I replace the feed rollers as well? Will that maybe solve the problem? Its looks like the sep. pad is not grabbing the paper. Maybe I...
  23. Replies
    10
    Views
    2,143

    HP 4345 mfp DF multi feeding

    Hi, I don't have any experience with this machine. The doc.feeder is multi-feeding the originals. I replaced the friction pad, but that didn't solve the problem. Is there anything else I can check?
  24. Yes, you can swap the drum units around. Also,...

    Yes, you can swap the drum units around. Also, remove the drum from the drum unit and clean the charge roller and cleaning blade. Maybe something is stuck on the cleaning blade.
  25. Replies
    19
    Views
    2,640

    Did you check the thermal fuses? They can be...

    Did you check the thermal fuses? They can be repaired by throwing them against the wall. Also, check the fusing frame around the HR bearings. Sometimes the frame cracks or break, giving sc codes.
Results 1 to 25 of 121
Page 1 of 5 1 2 3 4