Have you go with Ayanova?
I had a look at Eci software but is to much for me.
Type: Posts; User: vlad_robas
Have you go with Ayanova?
I had a look at Eci software but is to much for me.
I have replaced: developing unit + developer + drum + corona, all at once and all new
I have done the adjustment's and so far is ok
I will come back if is droping again
I apriciate the reply but it is developer, stick's to the magnetic screwdriver.
As I sayid developer is spilling in the front part as it shows in the photo39766
Drum is altmost at the end of life and charge is replaced preriodicaly because it is the only one that gets regulary dirty.
Drums that I use ar DU-104 and usualy they are doing 200%.
But if the...
Hi,
I have replaced Y developer and made the necesary adjustment's about 30 days ago (it has 5%). Now it had C2811 so when I open it it has Y developer spilled mostly in the front part. I know...
they are using KM C8000 toner
Hi,
Any normal paper with picture on it will stick (wrap) on fusing belt. I have tryed diferent 80gsm paper and it does the same, on harder paper ( from 100 gsm) it is ok. Fusing parts are'nt worn...
Hi, we have one and I'm strugglying to learn on it. You can see the post's.
One question: how do you set paper counting for big page ? "It was set to single click for 11 x 17 as well."
"laitang" advice: Color Registration adjustment, did it
Thank you!
Now C-3102 let's read the older post's
No.
It simply go in error code after a short period of time.
Should I try to go in Service Mode early?
Hi,
Before this code in the sim test pattern at 90 the coverage was't looking even at all. Consumable's weren't that bad and print was ok.
It stop's early after the start and show's this code.
Om...
Hi,
Is there a posibility that paper printed to go straight out ? Printed face to go out and not "face down exit"?
My problem: Paper printed is exiting face down and since is some kind of glossy...
check sd card contact's
I think that will be hard to find
Hello,
I'm not a KM trained tech. We have in our copyshop C6500 that is doing some white lines, very thin one's, like in the atach, is doing them mostly on black but I can barely see them on magenta...
As I stated early im not realy god with km but there is way to much black on the print, then is trowing 2557 error and cartridge is doing only 1/4 pages than before replacemet of the unit.
I'm in the right place?30727
This is actualy an OCE 171 but it is working with C250 supllies.
"initialize/stabilize" and "gradation" didn't help
I can't find tech rep mode.
Hello,
I'm Sharp tech I don't usualy do KM, other than our C6500.
I have a customer with this machine and about few month's ago I have replaced black unit with a new one but at that moment I...
Hi,
It doesen't always see the black cartridge. Someting like u open the door and close it and then it doesen't recognize it.
Now mostly it doesen't see it.
Cartridge's are all original one's but...
Hi,
My machine is jamming on plain paper but is ok on any other harder paper. This is only happening on full covered page.
Fusing belt was recently changed and jam is occuring in the fuser and is...
Hi,
My machine is having difficulties on taking 300gsm paper from bypass, from 20 pages first 1 or 2 rezult's in a jam code, usualy the first pages.
I have change roller's with new one's but the...
I have found a solution for now:
Removed all 4 glass protections between the laser and the printing units and the line is gone... I suspect that it has an airflow problem, but...
I has 2 week's now...
In the waiting for another dev unit to put on bk I have emptyed dev unit's and switched developer inside. (bk unit is now with yellow dev in it and the same switch with the other one)
This should...
I have come to the conclusion that I have to change developing unit on bk.
And I have come to that conclusion becouse I have exchanged bk and yel unit's without closing the front door and only trick...