hey jake sorry about the delay, been running around turning gray. lol
Yes the cust replaced the clock module/battery to clear the error codes they had. now the copier boots up but all the paper...
Type: Posts; User: jprecht
hey jake sorry about the delay, been running around turning gray. lol
Yes the cust replaced the clock module/battery to clear the error codes they had. now the copier boots up but all the paper...
hi am a ricoh tech, but one of our custs has a color workcentre 7525 they replaced the battery module, and now the copier has a mssg saying incorrect password and insert sim card the origi
nal...
Ive seen this on a # of ricoh models and i have to agree with the other 2 techs. make sure the contact points are clean and that they ARE going to make a solid contact with the pcu. inspect the HV...
Hi Arnie, The fact that your skew is happening on both color and b/w steers me into a mechanical cause issue. You can always perform "line position ajstmnt" in mode 5 of the service mode. if you are...
hi huntington beach!!! I grew up in huntington park. lol went surfing alot way back when.:cool:
Both of these guys are on the money with their responses. I'm wondering if your skew issue is...
I'd say you are pushing the limits of this box, with your test prints. when you say you recalibrated what sims did you use? your exposure ajstments are in sim 46. but you can change "other things" as...
Hi,
Have you verified that it is indeed the finisher @ fault? I have had numerous jamming calls due to the two "exit switches" located in the switchback section due to "heat failure" as they are...
Hi, when you say you "recalibrated" did you mean your "procon ast. or "forced procon" sim 44' 2 or 4 ? also hows your humidity level around the box? down here in the gulf coast we have ALOT of...
My Friend, YOU!!! Would NOT BE a TECH, if you didn't have a "go for it" gift.!!! Yes we often stumble or have to get the laptop out or even "THE BOOK(BIBLE) So Bloody WHAT???? This "job" requires...
I n I, you brought the fuser back to the shop and it gives the same "low temp" code.??? Obviously there is an "issue " with "that" unit. My apologies 4 previous post. is obvious you have an...
While I agree with all the previous answers, I have found over the last 25 yrs that sharp's are prone to this problem in wintertime, especially when they are located in basements or "on site work...
this prob/solution discussion is why we are on here. I'd like to also add my thanx 2 wazza 4 pointing out something thats easy to overlook!!!
IGOD its funny what will come up in this category i'm cringing @ the thought. D Barry did a fine job of covering all the low points. I had my first@ 18 in the military and then again @45. they don't...
hi I have to agree with srewtape!!! Your Best BET is to get the "NOMINAL VALUES" from another IR then tweak them. is time consuming but gives you a solid starting point!!!
good Luck!!! Have had this...
IGOD!!!! you go blackkat 4866. Hats off to you 4 supplying the obvious, and being a gentleman about it!~!!
I'll REPEAT YOUR WORDS OF WISDOM "HIRE A TECH< IS WELL WORTH THE COST"!!!
this could be a number of things. i would start with the consumables first. how new is your toner?? is it OEM? if thats ok how about your imaging units? how worn r they? you could have drum pits...
Hey guys n gals i'm a 20 yr copier guy and we occaionally get this ink jet junk in here HELPPLEASE
on power up it jumps to an error screen and says "service...
Thanx to ALL who responded appreciate the info!
jprecht
My apologies for this model# error. my cust has both the 4500 and 5000 hp printers. I don't service these as he is a do it yourself cust. I would like to know if there is a t-belt reset...
Being a copier guy am familiar with the counter reset chips and fuses I have a cust with 3 hp 500 printers and would like to know how to reset the transfer belt count on these units. Thank you in...
Am familiar with both the bizhub and canon 3220 bxes and eitheir would fit your needs. both have advantages and disadvantages. I would look @ your service/supply sources and choose who is going to...
We solved the original post by sending him a touch screen/lcd as others stated ricoh had a real prob with the touch screen. in your case ????? easier to replace whole display from a junker if...
Call me @ wholesale copiers 1-512-247-7784 we can get you a used one cheap will have 2 ck on a price 4 you!!!
\ ...
is a common problem you will have to replace the touch screen portion of the conrol panel would b easier to swap kbds from a junker though. good luck!!!!
j
Faxman is probably right if it takes 400-500 shots b4 the degradation begins your currents/insulators r suffering. it's amazing how quik custs "pick up on a prob like this" very interesting you are...