Found two bad clucthes in ADU, one felt ok, other was really jammed on the shaft. replaced all 4, and machine is working as it should. C-0101, can also mean a stuck motor or clutch apparently.
Type: Posts; User: methogod
Found two bad clucthes in ADU, one felt ok, other was really jammed on the shaft. replaced all 4, and machine is working as it should. C-0101, can also mean a stuck motor or clutch apparently.
Update...
Replaced two clutches that drive off the M11, and have not had code again...
Ran about 20K clicks, seems good.
Both PF decks would cause this issue.
Will keep you updated...
Found error completely goes away when the paper feed deck is removed. I have a spare will test Monday. Any insight to what I am chasing?
will check closer at m11 but we looked it and found not...
Any one seen this?
Works sometimes fine, then today codes right away…
Anyone seen this on newer engines?
had a cyan dv dump month ago, cleaned everything real well.
anything I should look for?
any one have any experience with this machine?
We got it running pretty good, looking to find out how you do fine fold adjustments.
or is it locked in by the sheet size on the PSQ...
Is there a dipsw that limits or takes the limit off capacity of the stacker.
Seems like it is "Full" at about 2000 sheets of 11x17, should be able to do more.
its not at its lower limit, with...
i have one too that is brand new.
i was told same thing but exit is different.
and harness has to be changed.
not worth the hastle.
will a 1060 fuser run in a 2070?
Looking for a spare fuser and Turnover section...
chasing an issue, need to start fresh...
maryland, USA
Need a spare fuser, regular one.
have a few spare envelope fusers if anyone needs one.
before you do all that, you check the plastic hooks that lock the door into the registration. seen tray 1 and 2 jam when 3/4 dont and it was broken hooks.
I have that, ru509 is not listed as compatible. But the ls506 install book shows it can downstream the fd503… can’t get answer just have to try it..
engine - ru518, iq501, fd503, RU ???, LS506
Will a RU509 work? or do i a need a RU510?
install books show the LS506 is compatible with the RU509, but the compatibility chart does not show it...
Getting too much skew out of the PF trays.
100# cover runs straight from tray 2.... but not tray 4 or 5.
cleaned everything, the pre-registration roller in the PF unit looks ok...
I have...
Frankinsteining a c3080
pf, engine, ru518, iq, fd503, ru509, ls506
will the ru509 work before the large stacker or do I need a ru510?
Can’t find it wholesale anywhere, any aftermarket that’s good?
Bizhub 950
Fixed, needed to let fiery update all patches, unplugged from engine.
seemed to keep the fiery online whereas keeping it connected kept making it disconnect.
working well... minus the...
clean install with new hard drive on the fiery.
is there any place i have to set the IP for the engine side?
also note i can not format the hard drive, or go back to the internal controler. ...
i am not employed by KM.
its ok ill get it monday once they approve my account.
thanks but i have the FIB - wont work without a login to EFI.
please...
i dont have access to UK site.
send me both 2.0 and 1.2 if available...
thanks,
need the MIC-4160 reinstall ISO.
thanks,
update firmware, we had same issue, blue start button not working.
had to update twice to get it to work right.
Firmware up again, had same issue w 2070.
do you have iq installed?
yes its called the SLITTER DUMMY bypass...
need one if anyone has done an install recently.
6020960210