You didn't mention anything about the transfer belt? Check and clean the sensor for the belt unit. I've had this happen a few times. I generally make sure everything inside the unit is as clean as...
Type: Posts; User: bilyahn
You didn't mention anything about the transfer belt? Check and clean the sensor for the belt unit. I've had this happen a few times. I generally make sure everything inside the unit is as clean as...
On the slower units under 62 PPM i use the 850RT kits.
On the faster units I use the 850RT as the feed roller and the 1466 as the separation roller. (Get flat spots on the separation roller if you...
Had a problem yesterday with F2-78. Toner all over the inside. DV brush what extremely thick. Removed the DV material and the mag roller was caked with dried on toner. Cleaned the mag roller and...
Are you using OEM or aftermarket toner? Have had recurring issues with aftermarket toners.
Good luck
Bil
I had this happen on a 4071. jams with no jam code listed then it would code out with an H5-01 error. Replaced the POD1 sensor and all was good.
Good luck.
Bil
I had this recently and was scratching my head. Fairly new machine BP series. Wound up being a full piece of paper folded up and sucked into the belt unit. Fuser was hard to turn by hand which gave...
Had this problem on a MX-5070. After a lot of troubleshooting and boards changes (recommended by Sharp) our tech rep said try an end of lease procedure on it. Worked for us. Might want to try this...
Main charge color problem. I would first try re-seating all of your color drums. Then start troubleshooting your power supply.
Good luck
Bil
From other posts I've seen this may be an app problem. When this happens to me first thing I do is install latest and greatest driver (which I see you did) then change the advanced driver setting...
Sounds like you need to replace the HDD going by the symptoms you listed.
Good luck
Bil
Are they looking for color or B/W. Also not sure what you mean by average speed?
All of the new BP series will run this weight but not sure about 2 sided for some of the slower speeds.
Good...
No unfortunately currently unable to get this board from Sharp or Hytec which I find unusual. So I did as you suggested and removed the upper web. So far there haven't been any call backs.
Bil
Sorry but Sharp no longer allows access to these codes. Not for a long time now.
Bil
Happy Thanksgiving to everyone!
Just got back from a class and if you are a sharp dealer they have made it really easy to reset the admin password. Go into your IDNC Service website then your...
I had this happen within a couple of days of a new install. I pulled the charge knob then pulled the drums out slightly and reseated them. Issue hasn't returned.
Good luck
Bil
I last note on this call. I did update the firmware but during the process I got the 121 fuser error. I'm wondering if you can do the update without the fuser installed. I only have one of these so...
So got it fixed. Looks like there were 2 problems. Replaced the duplex sensor and that resolved the 620 jam code. Could now copy and print 2 sided except for 1 computer would not print 2 sided in...
Good morning all
I have a Sharp MX-C507F that is giving jam code 620.01A. This code is not in the Sharp manual nor does a google search find anything. Basically what is happening is whenever 2...
I have had this happen on 2 7570s and the fix both times was to replace the panel assembly. Also get a lot of u9 codes with this series. I just reseat the connectors for those be careful of the...
I don't normally mess with those unless they are damaged, then I remove them.
I clean the exposed side to get all of the black off of it then run the emory cloth on the underside. Can't really sand that part just run it back and forth to clean any loose debris. I DO NOT take...
Interesting. I thought about doing this but I will let you know. Thanks for the information.
Bil
I personally clean the grids with 400 grit emory cloth whenever I take the drum unit apart. Makes them last quite a bit longer and surprisingly cuts down on the arcing problem. I know this is not a...
I will give this a try this morning.
Thank you
I looked at the drive gears but did not remove them. But I can advance the web in simulation so I think the gear is good but I will take a CLOSER LOOK.
Thank you