Increase the resolution by one step to slow down the paper feed. The doc feeds on this series have multi-feed problems when the resolution is set to 200x200. This has worked for most of our C360s...
Type: Posts; User: Kmdurrin
Increase the resolution by one step to slow down the paper feed. The doc feeds on this series have multi-feed problems when the resolution is set to 200x200. This has worked for most of our C360s...
I've seen this happen when the background removal settings are cranked up too high. Maybe check that if running a fresh set of gradations doesnt help you.
Has anybody tried this? We have a group of Di5510/7210s that we would like to use as fire came machines, but the developer has been discontinued and is no longer available from Konica. I know that...
I have a client with a Di7210 that needs a toner refill desperatly. The particular client is working in a forest fire camp and the machine is installed in a tent in the middle of the woods (not...
Pretty much this. Its easy enough to diagnose. Remove the exit cover and look near the back of the machine. It will be pretty obvious if the toner drive is gooched.
Anybody remember what the contoller type is supposed to be set to on a C350 with a Peerless Xtreme VR. Yes... I know its a horribly shitty controller, but the client is a forest service office that...
I cant speak for Victor, but my black is about 2% used and my colors are all about 40%. The age of the IUs seems like its not a relevant factor in this issue. The lines are consistent between all...
Oh my god I'm stuck on a C654 thats doing the exact same thing. Anyone know what causes this?
You can also accomplish this with a small network hub. Just make sure the IP settings match between the computer and the printer.
In my experience KMBS will never send out a machine with current level firmware. We make is standard practice to update during our initial setup, and it solves a lot of problems before the machine...
If I were you, I would just start the whole damn thing over again. Go into service mode, initialize all the machines network settings, flash the firmware to current, and try again.
HELP! I have a customer with a C450 that recently had a NVRAM failure. We had to do a NVRAM reset and a total memory clear to get them up and going, but now the machine only gives access to 100...
Mr Bill - The lawsuit regarding early voting rights for military service members is not about stopping it... its about extending that same right to non-military citizens as well.
Regarding your...
You mad bro?
What is the IP of the computer you're sending to?
They will. The only real difference between the two is the splash screen and the plastic labels on the machines panels.
I just had to deal with a C252 that some asswipe like you sold to someone. The transfer belt was shot, the IUs streaked like crazy, the feed clutches were destroyed, the registration roller was...
Check that the washers on the shaft of the rotation sensor are still there. If you've taken the sensor apart, then they may have fallen out. We've also used a very thin (like cardstock thin) heat...
Thanks Paul, but I already have all the manuals.
We've had issues with the drum ground on these models. Our workaround has been to install a washer on the front of the drum shaft and screw a piece of spring copper on to the machines frame so it...
I have a bizhub 350 that will, for whatever reason, only allow custom size to be used through the bypass tray. For the life of me I cant figure out how to get it back to auto-detect paper size. ...
Anybody know the part number for the side door (duplex, jam removal, or whatever you call it). I have a machine with a broken latch holder and it looks like the only way to fix it is to replace the...
Its a fuser high heat error, so I'd probably start by looking at the fuser. Are you a tech?
If it was "life-stop" firmware, then there are a couple of SW switches that need to be changed. Check the TSB for a list.
I've had very little success with secure print on the mac and linux drivers. I've been able to make it work situationally, but its inconsistent at best.