The codes are 4 digit on a 2540c, all codes changed with the EBX generation machines.
05 mode is correct for dev setup etc... code to setup black dev is 2404.
Type: Posts; User: mckinley
The codes are 4 digit on a 2540c, all codes changed with the EBX generation machines.
05 mode is correct for dev setup etc... code to setup black dev is 2404.
I would calibrate yes, after the erase lamps have been replaced is extra important as the calibration will be out due to compensating for the issue
05 2404 to setup the black dev on a 2540c.
You're dev is probably going too quickly because the erase lamps have failed. you can test them in 03 output mode, code 235 to turn on / off, you will need...
If you ever get another one that doesn't stop driving up, or doesn't drive 1 or both motors at all. (probably more unlikely now the machines are getting old)
Try disconnecting the connectors for the...
Not sure if they'll still be available due to how long it's been obsolete, but here's the part numbers...
41320735000 ROL-PICK-UP
41320734000 ROL-FEED
41320650000 ROL-SPT-513
or pm kit...
The main culprit is usually the ozone fan at the bottom right of the rear of the machine.
Although there's a modified one, I don't replace the fans. I take out the rubber bung located under the...
Might be worth checking the erase lamps, they burn out on 2330c - 4520c / 2540cse - 4540cse range, they normally start by, half the row for a particular colour failing, then go completely.
03...
Might be worth checking the RADF cover microswitch is making properly.
When the lid is closed it's possible for the microswitch to not press down enough and remain open circuit instead of closed,...
Hi, If you replace the clutch, no need to use the crimp connectors or soldering. Cut one of the wires on the old clutch and tie it around one of the wires near the connector on the new clutch and...
Inside the rear frame of the machine is the toner drive section, there's a sensor on that section which detects the toner cart has been inserted. The sensor gets covered in toner and can throw that...
BC, there's a bulletin regarding this happening on the 2555c-4555c (applies to 2050/2550 as well i believe)
I made a handy guide on these machines a couple of years ago with stuff like this added,...
I would bin the machine personally, they came out around the same time as the 281c, but production ended earlier & the 2500c was terminated for parts production 2 years ago.
I automatically condemn...
I can't provide a link for a manual as I only access the Toshiba server with my info for that stuff.
The code you want is 08 - 9164 (bypass auto-start) I think (that's the new code to replace 658)
that code won't work on an e2540c, it'll be a four digit code now (completely different)
you'll find it in the 2540c service manual.
As BlackCat says, the push type switch on the inside of the rear frame cuts the AC voltage to the IH board.
What you can do is, there's a metal tab that sticks out of the back of the fuser unit, it...
What codes are you typing in that aren't being accepted?
You do know that the codes on the newer type machines (ebridge X) such as 2540c are all four digit now don't you? & different codes than on...
If you want Fax forwarding (receive fax, but send it to email instead of it printing out), you can configure it quite easily through Top Access, under "setup"
we had an e455 give an image like this & it was the logic board at fault.
I have however also had similar from the /work partition being corrupt on EBX machines (5&C mode to check)
And I also had...
You can still change the tray size while print jobs are in the memory if you enter "Test Mode D" (08 mode) & set the tray size through that screen via the code for the tray in question (in the...
ah yeah, you're right, i forgot it was the original amazon like the 810 etc... you can't even get parts for them anymore
You'll need a scan enabler ( usb dongle ) to allow it to scan.
I don't think they're available anymore, but i know that in my part of the world they were around Ģ700
I would think it would cost you...
There's no one way bearing gear on the 5520c that fails ( only the 4520c & earlier )
Normaly a fragment of broken gear from the fuser drive assembly drops down in to the 2nd transfer section & gets...
Hi Buddy,
Could be a drum unit / epu starting to get tight.
Might also be worth removing the gears from the drum drive, cleaning the shafts & applying some ptfe lubricant & aligning the gears with...
Check the transfer belt to make sure it's free to rotate, as the bushings seize up on this model.
Check the transfer belt cleaner isn't clogged up / spring popped out of unit ( the auger is a long...
you're very lucky, on one site alone i have 14 of them :) & it's a 70 mile drive away, over my entire area i have 100's of them lol