Search:

I had a very similar problem with a M4555. Bad HDD. replaced with similar HDD, Formatted in Administrator mode. Loaded Firmware.
Would not fully boot and come to ready state. stuck on booting...

PSTEELERS,
Did you figure this out?
Having similar issue here
d7guitar

Take out the fuse, put in a staple, install fuser or transfer assembly with the power on. As soon as you shut the door the device will reboot. Immediately remove the staple. Reboot again. Counter is...

You are correct. I've seen this many times. I carry window strip insulaion for this fix. since it already has sticky tape on one side it works great.

Following behind certain techs. You know, the ones who use super glue and electrical tape to fix everything!

When my client sends a fax, their header information is printed over the upper text in the document, making it unreadable.
It's an ERM (electronic medial record) program that they are printing from...

Had same problem but i was able to get my web server to show up correctly by doing a cold reset, then factory reset, then reboot.
Have a great day

Searched the Forum but didnt see anyione ask this question so here goes??
I have an envelope feeder that has one way gears that are slipping but i cant seem to find a parts manual for it.
Looked in...

There are feed solenoids for trays 2,3,4 and 5. These solenoids have a noise deadening foam strip attached where the arm contacts the body. These foams will degrade over time and the adhesive will...

you're right. I am not selecting the 2nd "ok". Thanks, i will give that a try.

I am also having this problem.
Although I CAN log in as supervisor and change the admin password i still receive authentication failure.
I see the Adminstrator1 listed as, login = "admin". Then i...

It could be incorrect toner!:mad:

Found the problem with both trays. First tray, the separation roller was not snapped in all the way. Even though i had checked it several times by pulling forward on the roller the torque limiter...

Tray rollers are new. I will check the registration rollers. The cassette side guides appeared to be fine, but i will take a closer look at them too.
When i troubleshoot this week i will update...

Has anyone seen this problem??? (8x11 plain paper)
Symptom 1
During a print (or copy) job the device will stop and display a "load Paper" message for that tray (in my case tray 5).
The tray DOES...

Where i work a sales lead from a technician is paid to the tech by the company, not from the salespersons commission. I would be pissed too if i had to share my small commission with anyone. I know...

I agree. I am not being told to be "hit and run" by my service manager. I am being told to get my parts costs down, way down. I tried to explain to him that some of the other techs i follow are hit...

Sometime the amount of calls you have may make you feel that you have to get to as many clients as possible in one day!
Everyone is down, or maybe a tech called in sick, or you maybe are covering...

The "dip" in restocking your major accounts must be done manually. Once you have a years worth of data keep their supplies steady based on that data. if it's mostly schools you could try using...

I guess the job fits me pretty well or i would be doing something different. this job has a lot of perks, being autonomous to a point, traveling, different everyday, challenging, using both our hands...

:cool: Welcome Aboard!

LOL:D

So after clearing the code the machine comes ready to make a copy???
Have you checked the fuser temp under "analogue" to see if temps look good?
I would guess the machine is rotating the fuser and...

Or has anyone tried to use one for service calls?
With the surge in electric vehicles, there must be a growing market of buyers.

Is there really a savings to be had?
After trading dollars for...

I listen to AM radio in the car (workdays) if i am bored of music or just need something else to keep my mind going.
I listen to Conservative and progressive talk radio. Sometimes i find myself...