did you check the feed rollers??? and also check the vertical guide rollers there is a white roller with a spring that runs throw the middle of the roller some times the hooksthat hold the spring ...
Type: Posts; User: kwazimoto
did you check the feed rollers??? and also check the vertical guide rollers there is a white roller with a spring that runs throw the middle of the roller some times the hooksthat hold the spring ...
Was anyone heard about Savin dropping smaller Deals in your area or one that just use Savin for a second line???
work hours are 7:30 to 4:30 but when we get to the first call varies do to travel time and witch tech goes we have some that are not go getters if you know what I mean..
we are getting a error code sc400.. Have replaced density sensor ,transfer belt asm,and the engine board, and all cart. one at a time.. and the code still comes up does anyone have any other ideas
...
canon 105's had three that have hit the 29 million plus mark now have 7105's over 10 mil ad still going great
we sell and service three brands of copiers,four brands of printers, wide format and riso.. yea it is alot of fun
I have a Gx 7000 thatis putting a cyan line at random spots ..It is thin and length varies and it is not in the same spot.. this is a new machine only about 250 prints on it..
any ideas would be...
hello
yes I like my job been doing it 20 years would not change it,, yes customer bring you done sometimes and some company drive you nut but for the most part it is a good job..I live in Montana so...
wishing all of you and yours a Happy and save holiday season..
May God Bless you all..
I have found that if you are loading firmware .. that the SD can be to big and may cause that code .. smaller is better...was using 2G card it errored out but used 32M card worked fine
Thanks for your help used a 32M card and everything worked out great.. must be something to size...LOL
Again Thanks
yes to the unzip files that was done...
I am getting the code when trying to upgrade firm ware machine works fine... doing that because when doing booklet finishing on this machine some of the prints come out upside down.. was told to up...
getting a SC819 616C when I install a SD card to upgrade firm ware...Yes in slot 3..
down loaded firm warefrom ricoh /savin site .. made folder titled romdata ,made folder in side that one for G133...
have you jiged the front door and watched the toner bottle spinning it sounds like something wrong with that to me(toner bottle drive asm) .. you have replaced most everything else...does it ever...
does this machine keep running ??? like it is trying to add toner or just keep asking for toner???
first look at the connection on the back of the fixing frame some times you have to put washers behind it so it will make a better fix with the connector in the rear of the machine..and some time...
likeoze said your drum has reached the end of life and needs to be replaced more then likely they all do.....
question does it read the right size of paper in the the DF?? and what is the jam code??? and what size of paper does it read there in service mode???
yes I do it is a minolta got it as a trade it came with 3 cases of toner when it dies I will junk it and get another one..LOL.. I am a canon tech but have but was a minolta tech...
what cable r u using to format the hard drive ??? also you have to make sure that you have the latest ver.. of format or it wont work either.. is this a canon hdd or from another vender ??? If all...
The right door actuator for sw3 can get bent and cause this problem.. or the switch goes bad...switch part number is wc8-5178-000
check the connectors for unit number one and number two.. the other thing to check is the front door interlocks...along with the sensor in the handle asm. that screwtape talked about...
Also check the little black roller that are below the gate that screwtape was talking about the get toner built up on them wish stops the paper so check the lead edge like screwtape said.. also the...
the 3300 is the same as a 3300g... like screwtape said check the dimm but yes the Hdd could be getting ready to go .. if it was not been replaced before it is a good change ...does it take a long...