Search:

Type: Posts; User: Kopyrtek

Page 1 of 17 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    2,898

    [Error Code] Re: S12-103 RISO HC 5500

    The wing motor has become stuck or is not working. The two chrome ramps on the exit of the machine are the wings that bow the paper when it comes out. They move to different positions for different...
  2. Replies
    17
    Views
    3,555

    Re: Floating print position

    The disposal motor will be hard to find. Easier to buy used GR on Ebay....keep it for parts only. The drifting you have is b/c the timing and giude rollers are not parallel. You can test by running...
  3. Replies
    6
    Views
    1,950

    Ditto.Check EBAY and buy a machine for parts only...

    Ditto.Check EBAY and buy a machine for parts only if you plan to run it for a while.
  4. Replies
    5
    Views
    1,669

    Check your feed tires and stripper pad for...

    Check your feed tires and stripper pad for wear.Clean the tires with soap and water for better grip.If the pad has a cup feel to it, its time to change it.
  5. Replies
    3
    Views
    1,027

    More than likely the ink has separated.More test...

    More than likely the ink has separated.More test prints will only produce more bad copies.If you can, clean the ink from inside the drum and replace the ink tube with a good one and then run test...
  6. Thread: Riso RZ 230

    by Kopyrtek
    Replies
    6
    Views
    11,493

    Check your messages triple d.

    Check your messages triple d.
  7. Replies
    4
    Views
    1,812

    Although they look damn close i will bet they...

    Although they look damn close i will bet they wont work.Even if they fit the chips will keep them from working and cost wise they are over $100 apart too.
  8. Replies
    1
    Views
    1,117

    Dont worry about the clear plastic piece.Cut a...

    Dont worry about the clear plastic piece.Cut a piece of master material and place on the drum under the clamp and run some copies until the drum can/is inked up.Then try and make a master.The T3 is a...
  9. Replies
    52
    Views
    34,500

    I have had good success with replacing the...

    I have had good success with replacing the thermistors and lowering the temp by 5 to 10 degrees.Also, i shim the fuser connector with a 1mm shim and turn AOF off.
  10. Replies
    10
    Views
    5,832

    You need to reset the paper size for the paper...

    You need to reset the paper size for the paper tray.One size for the 105mm and one for the 210mm.
  11. Replies
    3
    Views
    935

    LOL.Gotta love the "plastic" support for the...

    LOL.Gotta love the "plastic" support for the scanner.At least the 35/45 were made of aluminum (or a collection of some beer cans recycled).
  12. Replies
    3
    Views
    1,305

    60K from the product support guide.

    60K from the product support guide.
  13. Replies
    3
    Views
    935

    When you make a copy off the glass have you...

    When you make a copy off the glass have you watched the scanner?Does one side drag or is the scanner out of alignment?Only other thing i have would be to check all your mirrors and make sure they are...
  14. Replies
    3
    Views
    1,324

    Doesnt the spring keep the actuator out of the...

    Doesnt the spring keep the actuator out of the sensors?Or at least one of them?Have you tried paper in one of the sensors and not the other?Cant remember which is the home position for that finisher.
  15. Replies
    8
    Views
    3,078

    If its in the RA 5900 then its a C sensor...

    If its in the RA 5900 then its a C sensor malfunction.On the front of the drum are two sensors.One is the A sensor, the other is the C sensor.Clean, hit the reset button and retry.If that doesnt...
  16. Replies
    2
    Views
    715

    Usually disconnecting the toner add clutch will...

    Usually disconnecting the toner add clutch will do the trick.Sounds like it is too far over toned.Time to change the developer.
  17. Replies
    1
    Views
    756

    030-13101.Same as impression roller

    030-13101.Same as impression roller
  18. Replies
    2
    Views
    848

    Check the clamp on the color drums.Make sure they...

    Check the clamp on the color drums.Make sure they open all the way.They have a magnet on the ends that tell the machine when they are open and closed.They may be out of position.Check them with the...
  19. Replies
    4
    Views
    987

    Dont be afraid to use a bigger pair of pliers.Use...

    Dont be afraid to use a bigger pair of pliers.Use your feet to hold the drum and pull like hell...it will come out.The bottle has swollen up on the end.Been there and done that.
  20. Replies
    10
    Views
    1,087

    Glad you got it fixed.But you are right,how...

    Glad you got it fixed.But you are right,how bizarre is that!!Have to add that one to the list of odd fixes for Ricoh's.
  21. Replies
    5
    Views
    3,360

    zx81 is right.No need to change the clamp.Have...

    zx81 is right.No need to change the clamp.Have seen old style and new style run with no problems.
  22. Thread: RP3700

    by Kopyrtek
    Replies
    9
    Views
    1,572

    Take one to the hardware store and find one that...

    Take one to the hardware store and find one that fits.Costs a lot less and will last a lot longer.
  23. Replies
    1
    Views
    871

    Pull the front cover and remove the lift motor to...

    Pull the front cover and remove the lift motor to straighten the lift tray.
  24. Replies
    1
    Views
    1,838

    Does that one plug in on the main board or on the...

    Does that one plug in on the main board or on the drive pcb up front? Has been so long since i have hooked one up.Do you have to turn the user codes on also?
  25. Replies
    10
    Views
    1,087

    Vulkor, The harness has taken care of the...

    Vulkor,
    The harness has taken care of the SC704,705 codes also.Usually the harness is frayed where it makes a bend by the frame.Sometimes hard to find, but if you look hard enough you will find...
Results 1 to 25 of 410
Page 1 of 17 1 2 3 4