Search:

Type: Posts; User: Kyo fan

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds; generated 36 minute(s) ago.

  1. Replies
    4
    Views
    1,488

    Re: Is a TA 3050ci compatible with SMB3?

    Yup, it's either FTP or e-mail.
  2. Replies
    11
    Views
    4,446

    [Electrical] Re: Top cover switch shenanigans

    Finally managed to find the cause yesterday. After yet another careful tear down and inspecting every single wire for possible pinch or short, i slapped myself for making a rookie mistake. You see...
  3. Replies
    11
    Views
    4,446

    [Electrical] Top cover switch shenanigans

    So, I was working on ECOSYS P3055dn where i replaced clutches to resolve paper jams. I replaced those countless times, and never had this happen on any Kyocera device. After putting everything back...
  4. Thread: FTP Setup

    by Kyo fan
    Replies
    5
    Views
    3,963

    Re: FTP Setup

    @mincopier

    Thanks for this app, it works like a charm, even though it's from 2007 and made for windows Vista. The path is just "/" in Command center if you want scans to go to the folder you've...
  5. Replies
    4
    Views
    3,974

    Re: TA 520i cannot enter service mode.

    Open front door and than give it a try.
  6. [Error Code] Re: MFP Kyocera TASKalfa 3252ci (duplex copying is impossible)

    Hire a Kyocera tech.
  7. Re: Taskalfa 300ci command center not loading and other strange things

    You should do U021 to reset previous settings. Print the event log with U000 first, since it will wipe it. You can move the fax card, but you also need to move the fax memory from main pwb, since it...
  8. Re: Problem with TA2551ci strange printout ocasionally

    I would clean the lasers 1st, and check the contacts drums and devs are making on the back side once pushed in.
  9. Replies
    8
    Views
    5,894

    Re: TA3050ci with noise +error code

    That code is common for this series. One of the shafts on the plastic housing breaks:

    41634

    There are 2 gears on these shafts that spin with transfer release motor. When it breaks, you get...
  10. Replies
    4
    Views
    2,842

    Re: Ecosys P2040dn, often no takeup

    Post the event log if you can.
  11. Replies
    11
    Views
    7,124

    [Electrical] Re: M3040DN Keeps saying adding toner

    Replace the developer clutch.

    41397
  12. Replies
    9
    Views
    2,185

    Re: MyQ monitoring software

    For that you need to check "Set up IP filters" when installing embedded terminals with remote setup, and that saves a lot of time.
    The other way is to manually set IP filters thru Command Center for...
  13. Replies
    8
    Views
    2,836

    [Electrical] Re: image failure M and K on TA-4052CI

    Did that tech do all the adjustments from maintenance after replacing those parts?
  14. Thread: F245

    by Kyo fan
    Replies
    8
    Views
    5,472

    Re: F245

    When entering maintenace mode, open front or right door and try again. On this model, i would also inspect power source pwb for blown caps since it's not uncommon, and i've had F245 before due to it.
  15. Replies
    18
    Views
    2,884

    [Electrical] Re: CS 306ci No cyan listed on status page

    Push the pin of the Cyan DV unit in. If it doesn't help, it could be broken on the inside, in which case you need another DV.
  16. Replies
    5
    Views
    6,881

    Re: jam 4311, m2535dn

    It's fairly common for that gear to break. Replace it. There's a bulletin on it, and It has been reinforced with shape change.
  17. [Error Code] Re: Task alfa CS-6002i S001 on U412 after installing maintenance kit

    Make sure the optical section is clean.
  18. Replies
    2
    Views
    923

    [Misc] Re: Parts Comparison 4500 and 4551ci

    Never tried swapping drive units between color and b/w machines. These drive units last a lifetime, except for the clutches that rust over time (CLUTCH 50 Z35R), which causes paper jams. To me, it's...
  19. Replies
    3
    Views
    4,787

    [Error Code] Re: TASKALFA 5551ci-Error 5102

    If replacing drum unit C and charger didn't help, the next thing is high voltage pwb. Re seat connectors on it, check contacts, and replace it if nothing changes.
  20. Replies
    6
    Views
    1,574

    [CQ] Re: Cs-3050CI low toning on Magenta.

    I'm interested in values entered for mag roller voltages and thickness in U464.
  21. Replies
    8
    Views
    1,699

    Re: Task Alfa Side deck stuck at upper limit???

    That's most likely failing lift motor (the big and expensive stepper motor). These side decks had so many changes and fixes, it's mind boggling. Scroll thru service bulletins if you have access. You...
  22. Replies
    13
    Views
    4,495

    Re: Kyocera PreScribe Macro

    Yes, those are pre-printed and just need to be pulled after an invoice, and yes, this is one time job. So far, I managed to get it to pull from side deck and exit the same tray with this:

    !R! ...
  23. Replies
    13
    Views
    4,495

    Re: Kyocera PreScribe Macro

    Bumping this thread for a similar problem. Got a TASKalfa 6501 with finisher and side deck. It does up to 60k invoices at once monthly from a specific software. For this month, for every invoice,...
  24. Replies
    9
    Views
    1,962

    [Electrical] Re: 8002i fax system 12 not recognized

    Before changing boards, try U021 and U002. After that, upgrade firmware to the latest.
  25. Replies
    6
    Views
    2,274

    Re: DP-7100 on TA 5052 broken lifter plate.

    40905
Results 1 to 25 of 369
Page 1 of 15 1 2 3 4