Hi
It's error Serial Number PCB.
If the links don't help, just a replacement ...
Good luck
canon irc5185i error e350-0000
Type: Posts; User: victor_v
Hi
It's error Serial Number PCB.
If the links don't help, just a replacement ...
Good luck
canon irc5185i error e350-0000
Code such. I didn't meet him too. There is no problem now - the code was gone. Maybe the glitch was?...
Thanks for the answer
Hi, everybody.
Canon image RUNNER ADVANCE 6055. E273 error. In a service manual isn't present. What is it?
Thanks in advance.
The device printed on a network earlier?
If isn't present, whether check is in the device OPTION of the network printing. By default iR2270 the network printer isn't.
For the printing on a...
Thanks, Canuck
I understand value of a code.
Moreover, I checked Finisher controller PCB, Power supply,
Fuse box PCB, Transport motor driver PCB and Tray A motor
driver PCB. All PSBs work fine....
Hi, all
Why LEDs on the main controller of Fin-V1 are necessary?
Error E540-8001. In comparison with working Fin, doesn't light one LED. I try to find out - that it would mean.
Thanks in...
Thanks to all
The problem was with the activator of the stapler interference sensor and springs
Good luck
Victor V
Greetings to all.
Problem with Booklet Finisher-D1 (iR ADV 8105).
Stapling on corners - OK, the brochure - OK. Double stapling - only one back staple is present. The front staple is not...
Hi, All
It seems that there are a lot of similar problems with this ruler...
At me such:
I turn on the device - on the display a dark blue background, on it the line of loading is hardly...
Hi, everybody!
The client uses iR1133 for copying, printing and scanning. On computers various Windows versions are established: XP, Vista, 7.
Problem following: ONLY under Win 7/64bit it is...
Hi, everybody!
The client uses iR1133 for copying, printing and scanning. On computers various Windows versions are established: XP, Vista, 7.
Problem following: ONLY under Win 7/64bit it is...
yes, mjarbar, I meant it (sorry, it is difficult to me with English).
"Clear All" didn't help > it was necessary to replace the panel
thanks for your answers
Hi guru
Whether probably on iR2022i to make display calibration? The client is compelled to press the next buttons to set a mode.
Thanks in advance.
Hi,
E350
1. The bar code data for backup and the attached bar code data do not match
2. A fault in the Serial No. PCB is detected when power is turned ON
hi
What's model? What's written on a front cover or on the control panel?
I mean: to press a door (a hand), then turn iR on..
There was a similar problem, specific, with the micro-switch of a front door. The message at the display was just the same...
What about, at first to press a door, and then to turn the device on?
I faced such problem when the WORN OUT rollers badly moved a paper. As a result the sheet was late during giving.
Hi,
Level2 > COPIER > OPTION > USER > NW-SCAN
Enabling or disabling the network scan function
<Setting range>
0: Network scan function disabled [Default]
1: Network scan function enabled
hi,
There were two similar cases.
1. It was guilty image proc.
2. The power unit was guilty!!
* * *
o, ye,
but i am about right way
Hi,
Failure in laser
Failure in work of the low-voltage power supply
Can be will help..
Hi, colleagues.
I have solved a problem so.
6694
The rubber strip 30 х 10 х 3 mm is pasted
Problems aren't present more.
Good luck.
hi,
To learn the password it is impossible
You can remove the password:
SM > Data Initialization Mode (CLEAR) > PWD > Ok
After that you can set the new password
hi,
go to SM > Clear Data > PWD-CLEAR