You have to love general error codes. But you are quite correct Stirton. Looking at the source power is the answer.
I know this thread is old but still relevant.
Type: Posts; User: RAI
You have to love general error codes. But you are quite correct Stirton. Looking at the source power is the answer.
I know this thread is old but still relevant.
Well I need to jump on that bandwagon. After year's of no real problems, I’mknow seeing issues with system software and version 1.0 on the ic413. I've thrown in my $$$ contribution to the cause if a...
Well back to the drawing board. Swapped out the dev unit, same result. Changed 1st primary same result. Stopped machine mid test sheet (53) at 255 k only. Image light. Density on the tcr was in spec...
I'm back in there tomorrow so I will give the dev swap a go. I did do the toner revert. Thanks for the input.
I didn't have a k 1st transfer roller with me but it was on my mind to replace it. I will try that tomorrow. I will look at the 255 k as well on the drum at that time. Thanks for you ideas.
Hmmm aren't the C6000/c7000 units unique? I know the cyan is a different part number opposed to yellow or magenta. As this is the k unit is it possible to move it in place of a colour and tape the...
Yes I did. I'll look at the gear mesh but the dev unit I just replaced with a new one. I'm back at it tomorrow. Should there be any new discoveries I'll list.
Hi There,
Yes I had swapped the coronas and had forgot to mention this. It seems to be charge related.
Good Day. Looking for some help. I have a C6000 that had a worn K drum. Upon replacing it and doing the calibration I got a grey copy with back ground. I replaced the back developer mix and went to...
It's usually not boards that fail. I've had a couple of bad color units I've replaced in the last few years.
In most causes offending commands come from an object within the PDF itself. My experience has been a bad logo. It may not be practical but if you can send one job in page batches you will likely be...
This is not a driver option. You configure this through CWS. You can tell if the option is working. If you're monitoring via CWS, and you see thumbnail images as the jobs are in the processing...
When you say empty the developer tanks are you saying just refreshing the developer material inside the dev? Change the whole dev unit. Possible contamination at the dev mag roller. Contamination...
Yes KM firmware is the only firmware.
Sorry I missed the part of the test page from Cws being chewed. Firmware is cross compatible. So v70 can be loaded on ikon and km alike. As well rips can be interchanged with engines without issue....
Is the job showing in print on the printed log. Jobs that disappear are almost always caused by an incorrect or corrupt driver. It you use Cws to print test sheets do they come out? If NO change or...
I've seen this happen a few times with Fiery's basically the IP printing just stops and yet the spooler is running. I would delete the fiery driver using the fiery uninstall option. Reboot and use...
I'm working with an odd problem. I have a client with a Canon iR7186. They have a quality issue; in that prints vary in density. Client prints 90% 11x17 bond. I have vacuumed out dev unit. Toner is...
First off don't use cheap paper on a colour machine and with heavy coverage. Paper will curl when toner cools. However if it worked prior look to the paper thickness slider at exit side of fuser....
He's going to need the Ikon IC408 system software. I don't have Ikon SW for IC408. Anyone else care to step up to try and get him fixed up?
Are you using the correct OS controller SW? (Konica for Konica and ikon for ikon?) any crossing of OS causes a shut down 2 minutes after boot.
Is the line always on the bottom? Are you printing face up always? It looks like random electronic imaging issue. Maybe try reflashing firmware. I would test face up only prints to see if line shows...
They are going to damage the transfer unit. My thought is that it's just an image burn in from a prior job or a humidity problem once it warms up. Either way would explain pure randomness. Expert...
The interval of the band will tell you the source of the problem. I find all these machine suffer cross direction banding on the yellow. Drum replacement does help this type of problem. You can...
By chance is the toner non OEM? I just had a case of non OEM toner not transfering on heavy stock only. I rebuilt the itb assembly, replaced the dev, change the Chargers, the charge settings. Added...