OK, it must have been a bad day when I "discovered" the phantom color sensor. I cannot get the printer to behave like that again. Which is good.
Sorry for wasting your time
Type: Posts; User: thadwald
OK, it must have been a bad day when I "discovered" the phantom color sensor. I cannot get the printer to behave like that again. Which is good.
Sorry for wasting your time
That was my assumption.
It stops with a paper jam when the media color does not match the color selected on the screen.
I have a user who needs to print forms on carbonless paper. The media is 3 different colors, pink, blue, and white, interleaved. On this machine, the paper color needs to match what is specified on...
I am in the process of configuring/speccing a used Xerox C9065 printer with a booklet finisher at a school. The machine will also be used for some production printing. The machine came with a Fiery...
Hi.
I ordered a new copy board for a Canon IR 2525. The parts catalog illustration indicates that the foam mounting pads (8 pieces) are attached topart number FF3-4624-000. The part that my supplier...
I am now pretty sure the fuser is the issue.
It appears that the metal film inside the pressure belt has split in two at the white streak. This probably causes leaky induction heater eddy current...
What confuses me though is that there’s no visible accumulation of toner in the fuser area and no visible blemish on the fuser belts themselves.
Short of replacing the fuser, is there anything...
I have a Canon IRC7055 that has recently started leaving a white streak down the page. PG 5 prints with individual colors indicated that it happens with all colors. I printed a pg 5 with black 255...
Hi,
I need the service manual and parts catalog for the B1 Booklet Finisher on the Canon ImageRunner C7055.
Thanks
Adobe Acrobat X
Canon ImageRunner ADVANCE 7055, C7065.
Also a Xerox C75 press with a Fiery Controller.
Can someone recommend a workflow that allows printing documents with multiple page sizes? One example is a book that is mostly letter size but has several centerfold pages. What I'm looking for is a...
The C7055 was stuck and a reset showed a black screen with the error message:
E748-2042
The manual indicated that it is one of
Hard drive
Main Controller 1
Main controller 2
Box test...
Aaannnd it was an incorrectly installed ITB. Pressure lever on right side did not engage ..
Arrived at this machine to troubleshoot a color alignment issue. It had a patch sensor out of range error and a patch sensor fail error.
Now it won't print black at all.
I am not getting a K image...
I was sent a GPR-56 black drum (pn 110C003[AA]) by mistake. Can anyone tell me if this part will work in the IR Adv. C7055 in place of the GPR-33 black drum?
Thanks!
Can anyone recommend a mobile scanner/printer that will handle 11x17 paper?
Either laser or inkjet would be fine. Mobility is a priority.
Thanks
I have a minor issue with an ImageRunner Advance C7055, where it prints dark grey with a light magenta cast and light grey with a light green cast. I would like to fix this by creating a profile with...
On a C7055, single side copy margins are fine but when I duplex, it moves the entire image down the sheet by about 1/4" on both sides. Size letter, normal orientation. Can anyone tell me where to...
I replaced the primary corona wire and the grid, and now the machine seems to work satisfactory. Those wires are fickle things. I had recurring issues with streaks; no matter how well I cleaned...
The spots show only on the black. The machine runs very little, if any coated paper.
I can try the drum clean procedure tomorrow.
This is interesting. I haven't solved the spotting problem yet. If this turns out to be the problem, what can I do to remedy it? will shaking up the toner do anything for me?
Thanks for the input.
The secondary charge wire caused the streaks. I first tried wiping it using an alcohol soaked pad between the jaws of needle nose pliers. It didn't work. it seems like the...
Thanks to both of you for your input. I'm new to this and any information is helpful.
Could either of you explain how a corona wire or grid can cause streaks or spots?
I had both assemblies out...
Please :)
PG 5 black at 128 density results in the following print:
28300
The streaks are consistent but there is no pattern to the white dots at all--other than the fact that there are...
I am still hoping for a mac driver that catches up with the PC driver in terms of functionality.
The notable functionality missing from the Mac driver are:
Not possible to saddle stitch...