I recently installed an MX-LC12 to an MX-7081 with a Fiery and performed a firmware upgrade. The customer was printing restaurant menus on heavy 2 paper out of tray 3 before the installation with no...
Type: Posts; User: niceville318
I recently installed an MX-LC12 to an MX-7081 with a Fiery and performed a firmware upgrade. The customer was printing restaurant menus on heavy 2 paper out of tray 3 before the installation with no...
If Adjustment 8, Image Density adjustment doesn't fix it try simulation 46-19, change AE Mode from Mode2 to Mode1.
In 2022 our company added Canon to our lineup of manufacturers. Sales have recently looked into selling Canon wide-format printers, i don't know which models specifically. The Canon Rep said these...
UPDATE Everyone!
I compared the non-working usb drive with one of their working usb drives in Disk Management. The non-working drive's partition was not Active. Right-clicking wouldn't help...
I tried two USB's i carry and they both work, one is formatted FAT and the other is FAT32. The customer's drive does work in another manufacturer's MFP down the hall, it just doesn't work in any...
I don't think the drives were purchased from a different source. I tried FAT32 and it doesn't matter what is on the drive, it won't access it but does recognize it's plugged in.
I have an Ricoh MP 9003 and the customer is using a marketing 120MB USB device with their logo on it to scan files to. The Ricoh recognizes it is plugged in to the slot but can not access the drive....
The problems i experience mostly with this series are:
- premature wear on fuser belts (as JR2alta mentioned)
- toner hardening and blocking the auger in, mainly, the black PCU. I used to just...
phil b, it was the only thread addressing that error. If anyone else searches for it like I did, I’m hoping they’ll read my suggestion and it will actually help them. Unlike you, a “tech?”, that...
Check the finisher entrance sensor first for paper dust, then replace it if it's clean and doesn't respond in the simulations.
wilkommen!
Our company became an authorized dealer within the past year, although we've been servicing HP for as long as I've been with this company. On paper the pagewide sounds too good to be true, lower...
its been a while since you posted anything about this problem. What did you decide was the fix action? I'm having the same issue in an MX-4050 and just ordered two new torque limiters for trays 1 &...
These models have that Mother PWB that's buried within the machine. Although it looks like a pass-through pwb I've seen them fail and cause problems that had me chasing my tail. Based on the items...
Current problem is this: Turn the power on and the machine starts booting like its supposed to. Once the count-up hits 17% it just sits there.
History: a month ago the belt shredded, up until...
I had a similar problem but replacing the mSata fixed it. take a look at page 7-39 in the service manual. It may help you isolate the problem.
Oops, I just realized the Tech Tip earlier...
Or like some of our Ricoh users name their MFP "Rico Suave". Soooo original
I've studied the ancient scrolls and the Greeks were the original PB&J inventors. Their process was rather primitive but they spread the peanut butter on both sides of the psomi with grape (or...
On these models I have also seen this problem, leading me to believe it's a primary transfer belt problem. I've found, on occasion, one of the PCU's cleaning blades flipped, binding the drum and...
Have you tried updating or re-flashing the firmware?
You say you're getting blank pages. So the mfp is not jamming anymore or is it still printing blank pages and jamming at the POD1 sensor?
...
I've also had to replace the fusing wiring harness. On the rear side of the fuser tray, where the interface connector is, the wiring could get crimped when you remove/insert the fuser. That didn't...
check the simulations (4-2) for this sensor: L1DO001 2 series installation detection
If the locking mechanism bracket is not engaging the sensor, you will get that message when trying to copy and...
That code refers to 5 continuous jams at POD1. With blank images, I would reset the power, clean the rollers in the paper path and check the sensors in Sim 30-1 along with the following out of the...
There's also a bulletin out about replacing the waste toner containers. Some of them have blocked the flow of used toner back into the PCU, wearing a ring around the drum and also pulling developer...
i apologize for not updating this thread, I replaced the LSU motherboard and have not had anymore occurrences of the code.