Hello.
Customer complains about whistling when printing or copying.
1) Drum unit replacement did not help.
2) Roll lubrication in the paper path also did not help.
The sounds do not appear when...
Type: Posts; User: Zela
Hello.
Customer complains about whistling when printing or copying.
1) Drum unit replacement did not help.
2) Roll lubrication in the paper path also did not help.
The sounds do not appear when...
From level1 press 139 * at the same time
Use of original toner. Remove the orange tape or toner moves to the developer unit. Maybe a bad position of the gears on the developer unit.
I am a service technician and now solves this problem with the machine ir2520 who has traveled 2,000 copies.
Replacement developer unit, photo-cylinder, change of DC and AC voltages to the...
Embossed groove in the paper about 7 cm from the edge corresponds to the output rollers at the exit of fixation are not in a plane but deflected factory.
Edge wheels about pushing paper in the...
Clean all rollers including registration, check the feed wheel in the paper tray.
It is installed on the machine finisher?
Control gears in fixation, the fixation of the film.
Is the leading...
Shaking multiple tubes can be recommended.
Currently we irac9060 new yellow developing tank about a month and drove around 12T copies.
Yesterday the whole machine apart and cleaned air paths with...
Greetings to all
I have the same problem, we 3x irac7055 and 1x irac9060.
The machines have the number of copies from 300T to 800T.
All machines have a problem with the yellow developing - lumps...
The combined administration of 3 containers of pod-deck C1, or the last tray pod-deck
Now I do not know exactly but tech 11M is printed on 80% carbon and until now it was going pretty good. about 1 month until it began to manifest itself slightly. and now it's about every 50...
Greetings to all
Lately, I have a problem with the paper misfeed fixation.
I changed the delivery door fixing with separators for the upper and lower.
The delivery assy I changed the rollers on...
You were right.
When cleaning the scanner I probably accidentally wiping cloth on the rail in the reader.
From the perspective of the mounted scanner could not see anything.
But when removing...
There are my light stripes when copying, and printing it is OK.
I have a suspicion scanner unit but I never found a similar problem.
28214.
After disassembling the previous January it by itself after a week became operational.
I do not know where she could be a mistake.
:confused::confused:
hello
I have a similar problem.
I disassembled i gear color hooper.
While it goes and then turn Replace Toner message.
Cogwheels crack what I had been altered but now they are alright.
...
hello
the same thing happened to me, but in the end I just changed (white) motor rotation toner was torn off the power cable in the motor.
motor repaired and returned :cool:
Fuser film iR1020 can not be used.
Diameter iR1020 film is larger and a shorter length film.
Personally tested.
Also, I needed :(
The machine we are transported to repair the company and the same result.
Power supply to the machine is 240V.
Power source is 24V.
After closing the paper deck to 3,9V discovery motor,
but...
hello everyone
Today I have the same problem but nothing helped.
Work performed:
1) new motor M4,5
2) new motor driver pcb
3) other DC controler
4) other dc power supply
5) other feed...
Please advice.
I'm seeing the IP1110 error E015-1056 and I can not find it anywhere. According to SM should it be something in the feeding unit but do not know what ........:confused:
Im use only canon genuine part and toner.
The print document have 4-20% toner coverage.
Im dont changed the government use the paper quality.
Hello
We have a problem on machines canon iR17xx the life of drums moves only between 40-70%. :mad: Which is quite a few.
A frequent complaint is to solve the problem.
If someone tip to...
The charging rollers of each color creates a coating followed by background on paper.
There are several solutions :cool::
1) replace the drum unit
2) disassemble the unit and clean the...
Finisher AB2 does not flag the output.
But I figured it out ....
They were dusty reflectors on the sensor UN24, which is before output.
I have a problem with jam 1320, sensors FM2-4254 I checked and tried in another finisher and they are OK.
But in mine after warming up the machine will appear again.
It occurs to me only PCB. ...