I have been trying to enter admin and CE mode on Konicaminolta C3110. Keep getting authentication error. Anyone know how to reset CE password on this model?
Type: Posts; User: bgbas
I have been trying to enter admin and CE mode on Konicaminolta C3110. Keep getting authentication error. Anyone know how to reset CE password on this model?
:mad: Yes Iv'e run into many of these that fail before their duty rating. Bad gears and or loud whining noise, the first model was terrible.
They have a new part number and these fusers are...
Here you go
Subject:
C455x shortly after power up.
Description:
C455x shortly after power up.
Solution:
CAUSE: Failed laser unit (C4551 - Cyan; C4552 - Magenta; C4553 - Yellow; C4554 -...
Hope this won't sound like an odvious question but, have you looked in your junk mail folder?
First set the copier to the defaults you want then touch utility/counter, user setting, initial setting, current setting, OK. I'm doing this from memory so it may not be exact, but should get you...
If I understand your problem correctly, you are getting the distortion not in the direction of the scanner movement but across from it. If so, remove the glass and make sure the scanner moves freely...
Also on the C351 HDD is included as standard equipment so scanning options are much better.
If it was manufactured as a minolta machine, it should have a serial number sticker on the left side of the main body.
Then you can enter that number in tech mode, system 1.
Fixthecopier misspelled, should have been powdered the blade as in setting powder or toner. I like his suggestion of changing out the blade.
Here is what I found for that code
Subject:
Intermittent C-3B04 (C3B04).
Description:
Intermittent C-3B04.
Solution:
CAUSE: Power problem in the fusing unit.
Try changing the cyan LED with another color, if the background changes color, you have a bad LED.
Amen brother, this sight has lost a lot of its appeal for the reasons you mention.I don't visit it as often as I used to.
I think Wagon is mistaking the 551, which uses a toner collection roller for the 550 which uses the mylar
I think faxman is correct you need the optional HDD.
The following is not your exact symptom but the solution may be the same.
Description:
Why is the message "Server Disk Full" displayed when...
Here is some more bad news for you. Good luck:eek:
Subject:
C-6701 at power up.
Description:
C-6701
Solution:
PROBABLE CAUSES:
1. Failed Overall Control Board (OACB).
May be the NVRAM.
I'm not sure if there is a recovery procedure for this model which you may want to try before replacing it.
Products:
bizhub 360
bizhub 420
bizhub 500
Options:
None...
Try this. They are the sensors under the shutters.
Description:
P-21 or P-22 shortly after power up.
Solution:
CAUSE: The registration sensors (UN20 and UN21) are dirty or they are unable...
These are the available Linux drivers at the konica minolta US web site
Postscript PPD Drivers
Version 30000.0000 2/23/2007
2/23/2007
272 KB
Cleaning brush motor failure to turn.
What kind of scanning? FTP to a shared server folder? SMB? Box Operator?
If all setting are correct it could be corrupt firmware or the infamous NVRAM problem. Hope this helps
Technical Advice Document (TAD)Konica Minolta ConfidentialTAUS0701860EN00 Statistics Last Used...
If you can access the public user screen, logout then enter admin screen with code of 12345678.
Must have Java for any of this to work.
Enter the IP address of your C350 in the address bar of your web browser. You can create your onetouches from the scan tab.
The I/Us should be covered with a dark cloth or paper to prevent light shock. But if you just pull them out then replace them within a few minutes you don't have to bother.
There is a special...
It's a decent machine with very little maint. required other than the regular pm items and possibly the 1st tray feed clutch, although with 350k it's probably been changed out.
Sounds like you...