Search:

Hi ,
Remedy : Below issue has been sorted out by replacing tension roller bush(broken) in the TTF unit ,Now machine is working fine

.6211562116

symtoms: Random Horizontal white stripes only...

Hi

in this case replaced the toner supply roller and dv unit Also but issue remains

Hi
it’s a random line , measuring the distance couldn’t help me

Hi ,

symtoms: Random Horizontal white stripes only on the rear side of the machine which is perpendicular to the feed direction.

Action Taken :
1. repalced the TTF Spiral roller.
2.replaced...

SYMTOMPS: 021012: Jam Code (Staple Finisher-N1) 1012
Type: DELAY
Sensor Name/Description: Finisher Feed Sensor Delay jam
Sensor ID: S102
Paper Jam only in A4R single and duplex , A4 is working...

Hi

I am also having the similar issue with inner finisher F1(e56f).

Have u fixed your problem .

if yes please share the remedy that you done.

Hi

I am also having the similar issue with inner finisher F1(e56f).

Have u fixed your problem .

if yes please share the remedy that you done.

hi facing the below issues.
*Able to take copies from the platen

Symptoms : 1. Counter Data and serial no is disappeared .
2. Dadf is dead 3. No Network...

hi
As You mentioned ,adjusted the belt speed ,lines disappeared. Issue solved .

adjusted value -25

thank a lot

hi

A4 is the feeding direction.

Hi

symptoms : Black lines on the images.

action taken : cleaned the laser unit ,primary and pre transfer contact point ,dv drive assy ,drum drive assy and re re fixed .

1. Replaced primary...

hi

Harness between the sensor and df feed driver pcb has been replaced issue solved.

thanks

Hi

Symptom: 0100A6 jam code while Turn on the machine.

Action Taken :1.cleaned SR-21 sensor again same issue then Replaced the new sensor.
2.Firmware updated to the...

Hi
want change to change the job storage time to the maximum of 3days in secure print ,
logged in as administrator but the option is grayed out .

setting & Reg - fuction - print - job storage...

Hi all
saddle fold lead adjustment has been done machine ok. please have a look on the pdf file attached.

thanks & regards
gksapple

Hi

Having Saddle fold alignment issue in finisher-AN1 .please have a look on the adjustment.


thanks & Regards
gksapple

Hi
Doa with canon you mean full unit (pod lite deck -c1 ) or any specific .please clarify.


thanks
gks

1.media size from the pod deck lite c1 -330 X 482.6 mm
media size from the tray 1 & 2 -330 X 482.6 mm

2.yes all the packing tape has been removed.

3.Paper Picked and started to feed ,entered...

Hi
symptoms
Frequent paper jams from pod deck lite -c1 in a new installed machine IPR-C10000vp , when printing on 350 GSM media. same media is working fine from the machine tray 1 & 2.

Jam...

Hi
first check the finisher is detected or not . check the accesories status in the service mode.

COPIER (Service mode for printer) > DISPLAY (State display mode) > ACC-STS

SORTER 1 Dspl...

Hi

Remedy
Replaced the Registration patch Driver Pcb ,issue solved .

Thanks & regards
gks

Symptom : Error code E5f1-8000-02 & E567-8002-02
After dip switch adjustment for saddle staple position .
Cause :Finisher front door switch assembly spring out of position or broken
...

Hi
facing a quality issue in a recently installed image press c710

symptom: No consistency in each printouts ,color getting variations in every printouts.But no problem with PG test pages....

1.interchanged and checked the magenta transfer roller in the itb & primary charging assembly.

By the way its happening only in the magneta ,other colors were fine.


thanks
gksapple

Having copy quality issue in Magenta.please have a look on the attached image.

Issue : Rear side of the printout doesn't having the proper magenta toner filling in all media even plain media.
...