I need the service manual for HP Z6810.
Please contact me at michael.joseph@osivision.com.
Thanks, in advance.
Type: Posts; User: cscce
I need the service manual for HP Z6810.
Please contact me at michael.joseph@osivision.com.
Thanks, in advance.
Sorry. I missed that question (it's been a rough week).
The customer only uses genuine Xerox toner, drums, etc. and has done so for many years.
Since they have several of these next week I'm...
All colors or just black?
How many copies on machine, each color (KCMY)
Total Copies?
Have you replaced the black developer assembly?
The black developing unit has not bee replaced. One...
I am reposting this because there was an error in the original title.
Any ideas on this? (See photos below).
The black imaging drum was replaced but that had no effect (disregard the printout...
Any ideas on this?
Replacing the black imaging drum had no effect. My search thru the forum hasn't turned up anything similar (yet).
4365643657
After much wrangling with the hardware on a CLJ4730 copier trying to fix a 49.4C02 error, which occurred only when scanning to email, it turns out that the sysad had blocked users from manually...
I've had several 4525's give this error. In each case it was caused by the fuser drive assembly. There's a pad on one of the solenoids (to reduce noise) but the pads deteriorate over time and get...
I'm servicing a CLJ4730 with a weird problem. When scanning to email it gives a 49.4C04 error. Sometimes the error occurs before I finish entering the email address.
Printing over the network,...
Problem solved. Bad cyan cartridge. So much for user's claim that the previous cartridge "had the same problem".
Thanks! So, these solenoids are inside the ETB? If so, then this is not likely the cause since I installed a brand new ETB and that didn't affect the problem. So I re-installed the old ETB.
I am...
All print quality pages were perfect, except for the cyan page, so only cyan was posted.
I saw this same problem a few years ago on a HP CLJ 4005 (which uses the same print engine). Only cyan was...
Based on the quality pages and looking at the block diagrams in the manual I'm thinking it could be a noisy HVPS. The contacts on the cartridges and the printer have been cleaned, but that made no...
The print quality pages were all perfect except for the cyan page (see photo).
Also, the error log shows multiple 54.1E.xx errors (halftone calibration errors).
Firmware was updated to version...
I'm working on a HP 4730MFP (a 4700 with a scanner on it). The cyan drops out on the right side (see photo). So far the cyan cartridge has been (supplies are genuine HP) and the transfer belt has...
You could also try printing using a PostScript driver instead of a PCL driver, if there is one available for your printer.
Thanks for the help. Indeed, it was a hard drive problem.
cscce
I have a Canon c5030 that fails to boot. The progress bar appears but it never moves (stays stuck around 25%).
Controller 1 and 2 have been verified good (tested in another copier).
What could be...
I'm getting random black splotches on b& W prints and copies. See photo. Colors don't seem to be affected. What could be causing this? Contaminated 1st BTR? Replacing the drum had no effect.
...
The ITU has never been replaced. The page count on it is 109,000. Also, user says the problem has gradually become worse so it looks like the ITU is the problem.
Thanks,
cscce
I have a customer whose Lexmark c780 has intermittent mis-registraion. (See attached sample.) What is the most likely cause? I haven't found anything in the service manual so far.
Many thanks!
I have read rnelson's post about problems with Oce 600 and 650. I'm looking for more opinions so I can give management as much info as possible about reliability, parts availability, etc.
I know...
We are considering a proposal to service Oce' Colorwave 600 and 650 printers along with TC4 scanners.
How are these machines in terms of reliability, access to repair parts and service manuals, etc?...
Thank you very much to all who responded. The 107 key sequence worked, but only after I replaced the HDD. With a dead drive or no drive at all I could not get to SP mode.
Now I have another...
I have a SP 5210 that needs a hard drive replaced. I haven't been able to find the key sequence to get into SP mode. Reset>806182>C doesn't work nor does the old "107" code.
Any ideas?
Thanks in...
I had a HP CP4525 printer that was giving a 59.F0 error at every boot up, making the printer unusable. The cause turned out to be a failed DC Controller.