Good day all.
I replaced the Paper feed and Retard rollers on the machine above but the counter clear/reset option is not available in the tech menu.
Did some research but could not find a solution...
Type: Posts; User: AlbertK
Good day all.
I replaced the Paper feed and Retard rollers on the machine above but the counter clear/reset option is not available in the tech menu.
Did some research but could not find a solution...
It most certainly is a High voltage arcing problem.
What happened before the lines started. Did you or someone else replace anything or work with the harnesses, maybe pinch a wire? I would clean...
Hi,
I have a similar problem on a TA-3011i.
DP Plate lifts up but rollers don't turn to feed originals.....then Jam 9005 or 9011.
Did you manage to sort the problem with just the replacement of...
Thank you all for your input. I confirmed that all the eco mode settings and so on was indeed off and not adjusted and decided to replace the CIS, it did not make any difference.
I searched...
The marks on the drums is a known problem with this model however there is a technical bulletin with a drum upgrade. I know Kyocera has/had a drum compensation program for this model. Might be useful...
May I add, the copy quality has become worse over time...
Thanks darry1322,
The optics only consist of a sealed CIS Assembly with no mirrors only 1x slit glass....
I have also tried the original settings text, photo, text-photo but no major...
Both the Registration and Calibration settings are available in the service mode (System Menu).
The marks on the drums is a known problem with this model however there is a technical bulletin with a drum upgrade. I know Kyocera has/had a drum compensation program for this model. Might be useful...
Hay you guys, long time no post.
If I may, I have a problem with a TA-2200. The print quality is acceptable but the copies are really bad and the whole page is much lighter than the original. The...
Oh Hi..
As you mentioned, we used the "special" cleaning solution on the heads. Ran the deep clean about x3 and it was fine.
Thank you for the interest.
Hey...
Never mind. We managed to solve the problem.
Thank you.
Good day guys
I am having problems with a ComColor that is printing blank lines through the images.
It stated with lines across all the images, colour and mono and after normal and a few strong...
Hi. Thank you all !!
It does make sense but...If I scan, the original size and copy/scan size is displayed on the device screen as A4.....
It has the same problem when I scan to mail from the glass...
Good day all
I have a problem when scanning A4 to mail.
The image cuts 23mm of the top and bottom of the pages when scanning portrait and when scanning A4 landscape, it rotates the image and only...
Those machines still used Developer as carrier. The Developer in the machine is deteriorated and wont give you correct values.
If you can still find Developer....replace it. Check the values in...
I had the same problem on a higher volume machine and found a bulletin regarding the change of the TR cleaning section for models before a certain serial number.
Had to do Firmware and change TR...
The address book should be setup using the " Address Editor" on any local PC.
Not sure if it will work on newer PC's running Win 7/8/10.....
Not even sure if LDAP could communicate with these...
Hi. Thanks for the reply. I confirmed with KYOCERA HQ that the clutches are in fact the same.
This will be a repeat repair and as the fault was intermittent I already replaced the A5 modification...
Hi
I have FS-2100DN with constant jams from the standard cassette. I know it is the clutch...
Any one know if the PF clutch and the Dev drive clutches are the same? They do look the same, but I'm...
I have a 356ci running since June last year at a customer that does advertisements and fliers !!!? Wrong machine, I know, but he sourced it from somewhere and I maintain it. Thus far I only had one...
Hi. I had the same problem on same model and it was a broken gear in the gearbox of the feed unit for trays 3 and 4.
Hi
I would suggest you try to set the correct OEM (mode 265) for your country on the machine to display the Kyocera model.
While in that state of OEM the firmware will work and you can then change...
Hi
What happens if you test the sensors in service mode?
If the sensors test correctly you might have a Engine PWB problem.
Try updating the firmware before anything else.
Good luck
Thank you all.
The problem with just normal twain scanning is that it pulls all the documents to the PC as single image files. Imagine attaching a 30 page document...
I found NAPS not so simple...