i have problem with my t795 hp plotter. sometimes while its printing after cutting the paper . cutter wont disengage and i have 86:01 error. so i manually disengage the cutter and restart printer. i...
Type: Posts; User: hooman23
i have problem with my t795 hp plotter. sometimes while its printing after cutting the paper . cutter wont disengage and i have 86:01 error. so i manually disengage the cutter and restart printer. i...
Thats because you are so special. Im happy for you. Let me gather the infornation that i need.
I know how to install firmware. And how to replace eeprom.I wanted to know is it realy neccesery to rewrite the firmware that reset nvram. And i wanted to know is it possible to install c452 eeprom...
How far you meant?
Is it possible to install c452 eeprom on c652 machin? Is it necessary to reset eeprom. How can i reset eeprom? Is it possible with farmware rewrite? Possibl with A0P00Y0-F000-GQ7-D1 version.?
Can...
i have problem with my c652 error number c163 and updating several times the firmware. is it possible someone send me this reset tools A0P00Y0-F000-GQ7-D1.exe
my email address...
Replaced charge unite with an old c451 charger. Machin started with no error. Throw c2164 two times. After that table number changed. Problem solved
Today im goong to test wiring back of the hvi to charge unite with ohmmeter
Already tried another yellow imaging unit. The same code. Hv1. Prcb replaced. No luck
If i disconnect this connector mashin starts without any errors.
IC chip you mean yellow imaging unit chip.? I replaced yellow imaging unite with another one. It throws c2164 and c2162 immidiatly
If i disconnect this connector system starts without any errors.but it has problem in yellow color. by the way my erorr numbers are c2164 and c2162. Yes i used system clear. An i didn't check...
Any suggestion. Does anyone have experience in this problem?
I have exactly the same problem with c552. And i replaced yellow image. Hv1 and prolinter control board .anny sujestin
just saw it today
the problem is 3 switches above the fusing unit. just cute the wire for the middle one and make short circuit .. the problem goes away. i hade the same exact problem
i think 4.5 k
as you can see pictures i attached when i print halftone test print with 255 full color there is no problem but with 64 you can see small box and lines . i have this problem with all colors except...
i had exactly the same problem last week. and the problem is magenta unit. just change background voltage for magenta from 0 to 5 and press start key
as i mentioned the problem was not Mylar in the toner hopper . i disassemble hopper and maylar was ok . svg and vsp are 4.0 and 0.17 . quality is ok . a little over tone
After replacing ID sensor and running 30012 nothing changed. Vsg and vsp were around 3.9 and 0.8 but after 10 or 15 copies changed to zero or 0.1 . I cleaned all contacts and nothing changed ....
toner hopper is ok . you can simply check it with 580456 ... i replaced id sensor once before for this machine. td sensor for same machins at least 2 times. i have 45 copy and one 35 copy machines
i think the problem is id sensor.
vsg and vsp tend to zero after i changed 2210 to 1 and made 5 to 20 copies .. im goning to replace id sensor tomorrow
i have another question.. 2223 is toner...
30011 is around 70 and and every time i cleaned id sensor... i read somewhere that you mentioned after entering service code while front door open switching off and on ... and never use 2801 .. i...
confusing problem with ricoh aficio 2045e. after 500 pages of prints or copies they became lighter and 22092 change to 25...sometimes low toner blinking and after that i opened and closed front...