Hello all. Well I am moving and I have 4 copy machines here that I need to get rid of. No one is going to take them because they are as old as sin, but maybe some of the parts are useful to someone....
Type: Posts; User: engineerboy93
Hello all. Well I am moving and I have 4 copy machines here that I need to get rid of. No one is going to take them because they are as old as sin, but maybe some of the parts are useful to someone....
Howdy. I am looking for an Axis 7000 and a Fiery LX2. There is one on ebay, but I am not paying that much for old garbage. The shipping alone cost more than the actual value of useless hardware. I...
Recognizes the memory and I did the memory tests and everything passed with flying colours. I made a color photocopy and no issues the copy came out normal. go figure.
Well yesterday I decided to part out my machines, so I took the main board out of the mx-2300n and put it back in. Plugged in the machine and turned it on, what do you know it works! No error codes,...
I do not think that is why I got it for free, but I do agree they are crap. The machine wasn't giving me these codes when I got it, but until now. It is no big deal because it still prints and until...
I think this board is finished. The machine works, but every so often if I scan or copy a document it error codes and if the prints were to come out they would be all red. Thankfully I got this...
Alrighty, bought new memory and the codes went away. I made a scan later tonight and E7-01 came back up. Guess the main board has put up its white flag. I do not know if I will bother replacing the...
I am going to hold off for now. I found DIMM was bad, so I have ordered new DIMM. If I still continue to get errors with the new DIMM I will contact you about the control mfp.
Thanks
Alrighty all. I believe that the copier memory except for the 256MB card, is fried. So I went ahead and ordered all new memory to replace in the entire machine, and by doing this I can avoid the...
27623
Here is a screen shot, hopefully readable. The machine gives me E7-08 now, better than being a dead machine. I ran a memory test on the machine and one of the slots reads NG. One reads none,...
This is not an answer to my question. It does not matter anyways, as I have gotten the machine to work. I went back checked some switches I may have hit and everything is fine, but I figured I would...
Alrighty, 2nd attempt.
Yesterday I made some scans and E7-01 came up. I turned off the machine and cleaned out the dust using my compressed air can. I went to power the machine back up and it...
Does anybody out there in copier land have a working MFP CNT PWB for a 2300N?
Thanks
Opened up the back, everything looked fine. I blew out the dust off of the connectors using an air duster. Now the machine will not start up. Just three green led's keep blinking on the backside of...
Well when I got the machine, for free..., I opened up the back and checked everything out. All looked fine, but it is possible I may have overlooked something. I will open it up again to check for...
Thank you. I have the factory service manual and have performed minor service on this machine before and major service on AR series. What I am looking for is a technicians experience in this matter....
Howdy all,
Today I went to scan some documents and what pops up, E7-01. I looked up the error code and I am looking for some experienced opinions. What is likely going to be the cause of this...
I wonder if maybe the ribbon cable came loose during transport. I will give your method a shot since it doesn't involve tearing the machine apart.
Thanks
Yes, I guess I should have pointed out the page, figured it was obvious though. This is the 2nd time it has happened to me and it doesn't happen to all pages as you have seen. Yesterday it was very...
Suddenly my machine has started to act funny when I scan documents. It hasn't done the before, only started about a week ago. I have the machine on a ESPS filter with RJ-45 filtering.
Anyways, here...
Your location makes purchasing it unreasonable.
If you just assumed a standard 5-6% coverage, then you would just divide the toner cost by the yield and that would give you a price per page. If you need to assume a different coverage percentage,...
http://youtu.be/Ne2yFQPYYmU
Annette Funicello - Tall Paul
Yea I knew about the aftermarket drums, but I try to stay away from those when possible. I was hoping someone on here would have a sharp drum laying around that I could get for peanuts. I lucked out...
I did that already and it was fine. The problem has been solved, the fuser roller is flat.
This machine is going to have the following done to bring it to ship shape for commercial use.
4 x Main...