Have a MP307 that has been at the customer location since 2020. Since Feb 2024 its been going through a cyan toner every few weeks. this is not a heavy use machine and the use it does get is mostly...
Type: Posts; User: mommok
Have a MP307 that has been at the customer location since 2020. Since Feb 2024 its been going through a cyan toner every few weeks. this is not a heavy use machine and the use it does get is mostly...
Have a Lexmark XC4153 that has a 284.11 doc feeder jam code that wont clear. I have looked at the paper path and there are no obstructions and the sensor flags are in good working order. if I cant...
looking up what main kit i need from Lexmark xm7370, found several options a 225k and 400k kit the difference being one is NLRP and one is LRP. what does the NLRP, LRP stand for?
we use oem parts and supplies
yes, we have replaced all the components at the same time in an effort to nip the problem in the bud. Alas the the machines have given us the finger and laughed.
we have several mx6050v series machines that are regularly dumping k dv, never an issue with the color dv. we have replaced drums units, dv unit and MC PWB and surge protectors on these machine but...
we have seen this a lot as well. we have found the web drive control leaver gets worn out ( the machines we have in the field have an average of 5 million clicks on them and get heavy use daily). ...
yep everything that had to do with the stapler has been replaced with new parts. That said figured out the issue. when the stapler fired I notice the door was being shaken open a little each time. ...
Working on a FN22 that getting staple jams. the staple seams to get stuck the the top part of the staple unit, the staple doesn't get trimmed or crimped. the set seams stuck and can pull out of...
Im working on a BP-FN11 where the paper is not being ejected out of the finisher properly. I already did the timing adjustment for the disposition tray as it was way off, now the rubber flapper...
Replaced the cassette PWB and it started working.
P.S make sure the motor is seated fully to avail a grinding noise, took the gear holder back out to find the noise, could have saved a few...
I have been working on a ECOSYS M6635cidn that is having a tray lift issue. The history of this machine is a previous tech started this call and found the tray actuator broken (part number...
had this same issue on a few of these machines, what ended up fixing was replacing the delivery harness part number DHAI-6227FCPZ
ordered a dk-6305 from Kyocera, got an email saying the drum has been discontinued with no replacement. This leasd me to think they have stopped support the machines this drum goes in. Anyone know...
I have 2 slightly used heater lamps for Sharp Mxm654N 200V part number RLMPU0863FCP1. Lamps where installed before noticing they where the 200V part not the 120V, lamps where removed from the fusers...
had a simular issue, ended up replacing dv unit, drum unit and hc pwb. problem hasnt returned
have a mxm7570 that has toner getting into tray 2. cant figure out how. anyone come across this?
looking for parts manual or part numbers for the feed rollers for paitec es8000 pressure sealer
we have a mp 4055 that is asking for toner when the toner is installed. the history of this machine is as follows. original call for stated issue was late oct 2020. The tech at that time...
working on a sharp mxc357f which is a rebranded Lexmark XC2235. Its making a high pitch noise intermittent at the end of jobs. the noise sounds as if its two gears that are barely touching rubbing up...
working on a sharp mxc357f which is a rebranded Lexmark XC2235. Its making a high pitch noise intermittent at the end of jobs. the noise sounds as if its two gears that are barely touching rubbing...
using oem toner and pressure springs released fully. Haven't heard back from the customer so going to assume i fixed the issue as the customer would defiantly call if it wasn't fixed. I found that...
Sorry, its the mx-m7570
been having an issue where the lower fuser web not winding. toner gets caked on the web and starts rubbing the press roller causing a loud noise. Have tested the motor in sims and adjusted in sim...
For as long as I have been a tech my company has used Bio-T max to clean feed rollers. The company that make Bio-T max no longer sales it in 1 or 5 gal pails, can only buy in 55 Gal barrels. we...