Search:

Type: Posts; User: tee

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    2,379

    Re: Toner curve error ta 5053ci

    I have had this a few times and I resolved it by putting test pattern only on
    glass and leave the adf open in the maintenance Not sim codes. Try it a few times and
    it usually calibrates.
  2. Replies
    3
    Views
    778

    Re: MXB467F firmware failure

    Hold 3 and 6 and power on
    or when control panel works
    enter **36
  3. Replies
    1
    Views
    1,133

    Re: Kyocera P3055dn Check cassette 1

    I check lift motor by pressing the cassette size switches on the bottom right side
    when tray is removed, then I lift the feed roller unit up to check the upper limit sensor.
    It should stop the lift...
  4. Replies
    4
    Views
    936

    Re: MX-C357F 680.40K ERROR

    firmware didn't fix it.
  5. Replies
    4
    Views
    936

    MX-C357F 680.40K ERROR

    This copier is displaying complex page service check.
    It happens from the glass and the adf. What is the error code?
    Manual omits it in sharp and lexmark models.
  6. Replies
    5
    Views
    689

    Re: M3660/M3655 idn DP TX/RX sensor

    The m3655 is always breaking the adf frames and hinges.
    Kyocera has a bulletin that tells us to install the old m3550 hinges to
    solve the breaking frame problem.
  7. Thread: Developer

    by tee
    Replies
    7
    Views
    811

    Re: Developer

    Update on experiment on my in shop unit

    i have run 2,000 duplexed color copies and so far so good.
  8. Thread: Developer

    by tee
    Replies
    7
    Views
    811

    Developer

    Has anybody tried using sharp color developer in a ES2505ac ?
    I did and the color matches great. and the toner seems to add at appropriate times.
    I have to run it in shop for longer runs to see if...
  9. Thread: MX3071 F2-41

    by tee
    Replies
    8
    Views
    1,379

    Re: MX3071 F2-41

    I would check for any trouble errors in sim 22-6 . The problem with coronas, seals, drums
    are always a concern on all sharps. I test the discharge lamps , they have been known
    to be intermittent....
  10. Replies
    2
    Views
    566

    [Error Code] Re: Toshiba E3555C Code CE40

    Have you tried checking the IQC shutter?
    It can cause code when it doesn't open completely.
  11. Thread: wavy lines

    by tee
    Replies
    5
    Views
    621

    [CQ] Re: wavy lines

    Ended up being primary belt unit, even though full image was on the belt.
    2nd xfr roller tried but didn't work
  12. Thread: 6301 jams

    by tee
    Replies
    1
    Views
    1,075

    6301 jams

    kyocera 5003i jams in the sorter start area.
    Replaced sorter, connector to sorter, the AK-7110.
    Still jams.
  13. Thread: wavy lines

    by tee
    Replies
    5
    Views
    621

    [CQ] wavy lines

    I have es2505ac that has void areas on one side of the paper, running landscape direction.
    It happens intermittently on copies and prints. See samples.
    It has recently had new drums and coronas.
  14. Replies
    3
    Views
    690

    [CQ] Re: toshiba es3515ac ca00 error

    Here is the update that was done
    see attached
  15. Replies
    3
    Views
    690

    [CQ] toshiba es3515ac ca00 error

    tried calibrating and fails every time. copier just had black pm.
    image sensor shudder modification was done also.
    the patches are printed on the belt. black prints are somewhat blurry, but
    color...
  16. Re: kyocera taskalfa 7052ci blurred image in printing + copying

    Is there any toner spilling from that side of the machine?
    It looks like a drum/charge issue or possibly 2nd transfer if the
    polygon motor mirrors are pristine on the tips.
  17. Thread: Sharp MX2640

    by tee
    Replies
    4
    Views
    978

    Re: Sharp MX2640

    I have had Sharps do this before and it has always been a sensor.
  18. Replies
    1
    Views
    1,233

    Re: HP Pagewide color MFP P77940

    I resolved all errors except 61D2.3B error.
    airflow assy problem?
  19. Replies
    1
    Views
    1,233

    HP Pagewide color MFP P77940

    This copier was rebooting every copy or config page, until I unplugged the
    wireless jetdirect. It gives 81.04.00 jet direct event and 49.43.14 errors.
    Any ideas?
    I also saw 61.02.38 errors in...
  20. Thread: toshiba fusers

    by tee
    Replies
    0
    Views
    724

    toshiba fusers

    We are looking to trade or buy used toshiba fusers .

    Both color and black and white models.
    We have new sharp and kyocera parts to trade with.
  21. Replies
    14
    Views
    3,574

    Re: Kyocera 4002i Fusing issue

    I fixed a 5002i doing the same thing by increasing warmup ready center 5 degrees
    and low power center 5.
    You may have to increase edge if it tracks on the side, my 5002i ran for the full 600k pm...
  22. Replies
    8
    Views
    1,082

    [CQ] Re: M6026cidn color reg

    I had same problem and it was firmware , brand new transfer belt ,cleaned sensors, and
    performed coarse adjustment then the fine color calibration after the engine reset.
  23. Replies
    34
    Views
    10,432

    Re: Latest version of Chrome - Can't access Web Browser

    I have had this happen and fixed the problem by updating firmware.
  24. Re: MX5111N Copy quality automatically adjusting after every copy

    I have seen this on the older models when they need all drums and developers
    replaced and calibrated. Other times it has been the primary belt sensors needing
    a good cleaning.
  25. Replies
    7
    Views
    2,948

    Re: FS-4100DN Casette 1 Lift Issues

    I have had this fight many times.
    Check the roller assy and make sure it is not forced all the way to the top
    I also had a bushing slip off the feed drive shaft.
    Yes the gear breaks, but u can...
Results 1 to 25 of 76
Page 1 of 4 1 2 3 4