Search:

Type: Posts; User: amazed

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    1,485

    Re: 7002i / 8002i development unit problem

    Today cleaned up everything again and removed on 8002 toner filter (the fan runs with no problems), registration roller dust pad is clean.
    on mk replacement following is done:...
  2. Replies
    12
    Views
    1,485

    Re: 7002i / 8002i development unit problem

    genuine original kyocera toner


    Yes, each time, even tried to remove filters to increase air flow.
  3. Replies
    12
    Views
    1,485

    7002i / 8002i development unit problem

    Hi! We have 7002i and 8002i in one location and 7002i in another location and all of the machines have the same problem.
    The new development unit (or new MK) works pretty well until 30-50k copies,...
  4. Replies
    1
    Views
    1,104

    Kyocera dv-8305 vs dv-8505

    Hi!

    We have a Kyocera dv-8505m (FS-C8600DN) damaged because of improper installation (cracked gears)
    our supplier have a cheap dv-8305m unit (much cheaper, than dv-8505), so the question is:
    are...
  5. Thread: ar160

    by amazed
    Replies
    3
    Views
    516

    Re: ar160

    Developer should be replaced every 50 000 copies,
    If the toner sign is blinking - simply add a toner.
    if it is lit - you should change toner chip, or replace cartridge.
  6. Replies
    1
    Views
    1,320

    [Electrical] Re: FS-1135 MFP Panel firmware update

    Hi!

    Firmware update history is attached...

    22655
  7. Replies
    3
    Views
    774

    Re: HP 4730 scanner problem

    All the connectors \ wiring shields were checked... As far as I know, there were no any replacements of boards or units....
  8. Replies
    1
    Views
    850

    Re: Toner replenish on KM 2030

    Is the test print (for example sim 000) also grey? If not - try to clean optics section...
  9. Replies
    3
    Views
    774

    HP 4730 scanner problem

    The scanner/copier output looks like this:
    14393
    while printing is ok:
    14392

    I tried all calibration procedures and cleaned/inspected optics...
    Everything seems to be ok...

    Any help would...
  10. Thread: C50 Mita DC2050

    by amazed
    Replies
    2
    Views
    859

    [Error Code] Re: C50 Mita DC2050

    C-50 indicate problems with high voltage. Check charge/transfer coronas...
  11. Thread: KM 1820

    by amazed
    Replies
    5
    Views
    1,398

    Re: KM 1820

    We are using mostly compatible toner, works fine... If you want to use only original toner - you can save a bit by buying tk-410 or similar TK for
    a bigger a3 copiers (150k drum), divide it into 3...
  12. Replies
    4
    Views
    1,169

    [Misc] Re: KM 2820, 2010 Imaging Process Unit, Toner

    Yes, but probably you have to replace gears on the drum (pay special attention to the contact plates inside the drum)
  13. Thread: KM 1820

    by amazed
    Replies
    5
    Views
    1,398

    Re: KM 1820

    1620/2020 are reliable, common problems are - clutch on a bypass feed (I have replaced 2 or 3 clutches, have about 100-150 units)
    drum resource is usually more than 150k, there are also cheap...
  14. Replies
    4
    Views
    1,169

    [Misc] Re: KM 2820, 2010 Imaging Process Unit, Toner

    We don't have such model on our market (Russia),
    but it seem to be an ordinary kyocera for an a4 format..
    So you can use drum from other kyocera a4 format mfp or printer (with 100k resource) and...
  15. Thread: KM2530

    by amazed
    Replies
    16
    Views
    2,297

    There is a CF slot for firmware upgrade, so for...

    There is a CF slot for firmware upgrade, so for an upgrade you need a CF card and firmware itself...
  16. Replies
    8
    Views
    1,556

    after series of tests I acknowledged that...

    after series of tests I acknowledged that everything works fine, when the amount of paper in cassette is 500+ pages
    so probably the solution is to adjust a position of a cassette...(and check paper...
  17. Replies
    8
    Views
    1,556

    KM 6030 feed problems

    Hi

    I have new km 6030 (less than 200k copies) and from the very beginning there are problems with feed from trays 1 and 2 (large capacity).. Paper travels about 3-5 cm and then jams, w\o visible...
Results 1 to 17 of 17