Is it OEM ink, is it new or OLD (should have a date of manufacture stamped on it)? Take the ink tube out and the little cover door under it in the drum. In service mode are the squeegee and doctor...
Type: Posts; User: 20gaugeO/U
Is it OEM ink, is it new or OLD (should have a date of manufacture stamped on it)? Take the ink tube out and the little cover door under it in the drum. In service mode are the squeegee and doctor...
There's a small screen filter inside the pump (have to pay attention to the curvature of the screen when reassembling). If it is colored ink it can get gummed up from sitting around and not being...
Using generic ink? If it's runny and got into the one way gear of the squeegee gear can cause slippage. It was more of a problem on the RZ line. I think you can shine a light in the back opening...
Are these machines NEW? or new to you???
If you are talking Registration:
You can adjust each drums master making write start position. You'll have to burn masters for each drum and measure,...
The machine has pull out handles on the feed and exit side of the machine. My guess would be whoever moved and/or picked up the machine didn't use them and either stuck either the upper or lower...
There should be a date stamped on the end. Anything older than 2 years toss and start fresh
Yep it's trying to draw ink and failing for some reason thus the dry whistle sound. When it stops whistling you'll have fixed your problem
Reseat all the connectors and check that the clock / time is set correctly both in user settings and service modes. Firmware is up to 3.0.0 so what do you have on your machine?
There are multiple O-rings in the drum, have a real picture of the part you are looking for? I don't recognize that one. Or what's the problem with the machine?
I have 2 @ UG-36 speed license upgrade kits to make a 2554ci a 3554ci. Looking to move them at a discounted price. PM if interested
Parts Lift Guide Assy SP
p/n: 303R794110
Replaced the plastic pin with a steel one. $5 part and a 15 minute fix.
Take off the front and rear covers and blow out the dust, cut tie wraps and reseat connectors. That won't cost you anything, see what you see. If it still has problems you'll probably need parts...
The gear/screw has stripped itself out. You'll notice in the other video the combo is about 3 times the size, that was a modified part for when the smaller model stripped out. If you can find the...
From the amount of ink on the inside of the door and rails I'd also say your impression roller is probably caked in old dry ink. Can only scrape it off and clean so many times before you just have...
Did you just try some scratch paper to test? Any chance the sep pad peeled back the underside of the lead edge of the 150 gsm paper so now it's fighting it. Turn the paper and original around 180...
Did you take the clutch apart and clean the red rust off the faces? Did you put it back together so it still free spins?
The timing gear looks like a one way timing gear, sometimes you just have to...
Blow out the paper in sensors. Clean or replace the feed clutch. Replace the one way timing gear
Take 1 wire and lightly pull on it from both ends, then do it to the other wire. Like stretching out a rope. You are seeing if the wire is literally hanging by a thread inside the insulation
I believe that solenoid has 2 wires and a protective sleeve over it. Back in the day one of the wires would break at the U in bend. Cut off the protective sleeve and stress each wire and see if...
Congrats. That plate can get a hairline crack in it as well. 99% of the mechanical stuff you learn on the RA is used in any Riso made in the last 15 years. Sorry and good luck
Pretty sure the battery is just a key fob type battery on the main board if I remember right. I think it just keeps some default settings. Either way good luck with that old thing. Might as well...
Find a 255/305 or a 205c/255c or an FS-C8520/C8525
Just swap 1 and see if your problem goes away and start troubleshooting. The entire ADF just lifts off once you undo the 2 thumbs screws and...
We use Impact Technologies or TTR. Mostly it depends on the driver, some seem to be in a lot more of a hurry (TTR). Impact we always have the same driver so it works out great. Used Copier...
Is it Generic Ink or have a damaged RF tag? Try a different tube cause that is the proper inking operation
Huh? The paper sticks to the drum? To much lead edge ink or the sep finger rubber O-ring is broken and not shooting the puff of air
A better description of what's happening would help