Search:

Hi everyone,

I have a sharp mx-m3550 that when it goes to sleep mode, the customer can't wake it up. They have to unplug the machine,wait 15 seconds plug it back in and wait for it to reboot....

It sounds like its the paper feed tray upper limit switch CLUD1 or the paper empty sensor CPED1 for tray one and CLUD2 and CPED2 for paper tray two.
These sensors seem to fail intermittently. You...

How do you clone a msata chip?

hi,
I ordered a job separator and found out the lever is on the job separator tray. this took care of my problem, Thanks

Hi, I have a brand new sharp mx-2630n and if you look in parts manual under exteriors 2 part number 1&4. part numbers are LSOU-0274fczz and GCAB-1616FCZZ description delivery tray and delivery tray...

I have a mx-3070n in which I'm getting an error code E7-80 and E7-90 about every 2 weeks. I update the firmware using the emergency update
procedure with a jump drive with the firmware from sharp's...

Yes, I didn't see any solenoid in the parts manual for the mx-tr11 job separator. I'm wondering if the solenoid is already on the main unit or how the gate is changed to the upper tray. I believe...

I have this machine set up so copies and prints output at the bottom exit and faxes output at the top exit(job separator tray). Intermittently,the machine tries to send a received fax to the bottom...

I just found part number in a bulletin mfp-tb-1637. Thanks

I am having problem finding part number for the sd card for a mx-3110n copier. I was wondering if some one can help me in this matter.
Thanks

I tried reloading firmware but it wouldn't let me. I tried 56-1 copy data from hdd to eeprom but it just errored out.

I have a mx-b402sc copier in which everything was working except for the pullout keyboard. I tried a good pullout keyboard and it didn't
work in this machine. i put the original keyboard in another...

I have a mx-c402sc copier that makes a clicking noise when using the top paper tray. I can feel the clicking on the paper drive unit in the

back of the machine. When I use the second paper tray I...

I have a mx m453n copier that intermittently after going into energy save mode (sleep), does not come out of this mode.

It's supposed to come out of sleep mode if you print to it or if you press...

Hi I was wondering if anyone could help me. Is there a way to recalibrate the operational panel on a mx-354n copier. it seems most things work but
some don't line up properly.Thanks for help in...

Thanks. I will try that.

I have a brand new mx-3070n machine that has 230 color copies where the color is blurry. When I try to do TC 50-22 I get an error
Range_sub_M93. Since I get this error, I can't make this adjustment...

I have a mx-2615n copier that the customer says freezes up,They use sim 66-10 to unfreeze. The customer says it seems to happen
when a print job and fax job are executed at the same time. I'm not...

I have a sharp Mx-5111n that has a mx-fn11 finisher when duplexing occasionally i get a dogear fold towards lead edge front of paper and
it jams right at the entrance lever of finisher. I can...

Hi, I have an update. I changed the TC pwb and the copier started working immediately. Thanks for your help!!!

Thanks for your advice. I have a tc pwb and those clutches on order. I'm gonna replace tc pwb first then the clutches. Thanks again

Hi
I was wondering if there is a certain procedure to troubleshoot a mx-2640n that has a c4-00 code. if you turn off the main switch and turn back on
the machine goes in ready mode but when you...

How big is the dip switch and where on the main board is it located. I can't locate the dip switch. Thanks for your help

I have an Sharp MX-363 copier that a customer changed the Admin password and forgot what he changed it to. Is there any way to reset the password. This machine does not have Test Command 24-30 or...

I found the problem. When I changed the shaft from tb-1272 A pin that drives the gear for dv drive fell out so I had no drive for black dv unit.