Search:

Type: Posts; User: mtech

Page 1 of 13 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    4,130

    Check connectors to duplex and fuser bed. Try...

    Check connectors to duplex and fuser bed. Try pulling out the staple cartridge and reboot the machine or try another staple cartridge if you have one. I had a bad staple cartridge cause this issue...
  2. Replies
    10
    Views
    1,708

    [CQ] Every once in a while this use to happen to me....

    Every once in a while this use to happen to me. Wtroll is right! Change the toner!!! I have had more than one machine do this to me and it really was bad! You go to the machine and give it a full PM...
  3. Replies
    6
    Views
    1,399

    [Misc] You might want to check the microswitch that is...

    You might want to check the microswitch that is actuated by the green handle on the transfer bed.
  4. Replies
    24
    Views
    3,399

    What parts and manual spamming???

    What parts and manual spamming???
  5. Replies
    7
    Views
    2,255

    If you replaced both thermistors and the fuser...

    If you replaced both thermistors and the fuser rollers are okay, (mainly the lower roller because the bearings wear out) You will need to replace the DC controller. This is very common with this...
  6. Replies
    5
    Views
    3,713

    [Error Code] The main charge is located on the top of the drum...

    The main charge is located on the top of the drum unit and the sensor is located in the drum unit as well. The whole drum unit slides out from the front. You need to remove the brown cover and the...
  7. Replies
    5
    Views
    3,713

    [Error Code] 28-01 The charging on/off operation has been...

    28-01 The charging on/off operation has been performed five consecutive times since the charging trouble detection signal was detected at start of charging. (I can't stand the wording in some Minolta...
  8. Replies
    32
    Views
    4,247

    I remember one manual describing the fur brush....

    I remember one manual describing the fur brush. That always made my laugh. Oh yeah, does anyone remember Sharp putting out a bulletin showing how they were changing some of the part numbers from...
  9. Replies
    1
    Views
    1,198

    4030-3711-02 is the frame that runs up just the...

    4030-3711-02 is the frame that runs up just the side of the unit where the gears and clutch are. 4030-3701-02 is the frame that usually breaks. It is the whole middle of the duplex unit. They usually...
  10. Replies
    7
    Views
    3,115

    Remove the connectors to the HDD and see if it...

    Remove the connectors to the HDD and see if it boots. It will then give you a HDD error. If it does then replace HDD, if not then could be anything. If so, remove all peripherals from the box and try...
  11. Replies
    8
    Views
    8,638

    You can change which counters to display. Go to...

    You can change which counters to display. Go to copier>option>user
  12. Replies
    7
    Views
    1,360

    [CQ] Sorry, I read the post too quickly. You are right...

    Sorry, I read the post too quickly. You are right either way. Engine must be calibrated first. I remember having light cq problems right out of the gate with some of these. It was only with copying...
  13. Replies
    7
    Views
    1,360

    [CQ] How do the copies look if you take the machine...

    How do the copies look if you take the machine out of auto exposure and use manual (text)?
  14. Replies
    7
    Views
    849

    [Misc] Well you said you replaced the HVT so I should...

    Well you said you replaced the HVT so I should have read your post twice! did you try an all clear? I had a bunch of these do this to me. You could fix it by doing an all clear, but it would come...
  15. Replies
    7
    Views
    849

    [Misc] You may have a problem with the stupid front...

    You may have a problem with the stupid front guide that has connections to the HVT. I call it stupid because it sucks to replace as it has a big spring in it. When the machine is giving you the black...
  16. Replies
    5
    Views
    1,404

    Very nice and hopefully helpful!

    Very nice and hopefully helpful!
  17. Thread: Checking in

    by mtech
    Replies
    2
    Views
    415

    Welcome! What seems to be the problem with the...

    Welcome! What seems to be the problem with the mp4000?
  18. Replies
    17
    Views
    6,645

    Good call Paul! I think someone really needs to...

    Good call Paul! I think someone really needs to take a look at the manual!
  19. Thread: CANON IR7105

    by mtech
    Replies
    28
    Views
    8,177

    Sounds like the laser to me, check your settings....

    Sounds like the laser to me, check your settings. You can try to adjust laser power to see if it makes a difference. (if it works you still need a laser as it won't last) If you replaced all those...
  20. Replies
    14
    Views
    2,204

    Mr.Fixit is absolutely right! If they want to...

    Mr.Fixit is absolutely right! If they want to really keep the HDD from being tapped then they need to take possesion of the original and destroy it themselves. Pay for a replacement and the labor to...
  21. Thread: ar-m450n jams

    by mtech
    Replies
    18
    Views
    2,047

    I can not understand what you are now talking...

    I can not understand what you are now talking about, but try replacing the lift motor for tray 1. If you get the back of the machine off and fill the tray, run 500 copies while you watch the motor....
  22. Replies
    4
    Views
    1,251

    906/907 and 1106 etc. light copies again!!

    Replaced every thing you could think of, but light copies again! Come on really! (Seth and Amy on SNL) I mean really!! Premature developer changes, toner sensors, whole DV unit, drum, pm kits, toner...
  23. Replies
    8
    Views
    1,362

    [Misc] Vincent64, I am sure the switch is your issue....

    Vincent64, I am sure the switch is your issue. Even though their are other sensors, this sensor trumps them because the machine thinks the cassette is not installed. Rayjeek, the clutch in your...
  24. Replies
    8
    Views
    1,362

    [Misc] I remember a switch on the rear of the machine...

    I remember a switch on the rear of the machine that goes bad. It was a really common problem. Each cassette has it's own switch. The switch gets actuated by the cassette when it is closed. When the...
  25. Replies
    4
    Views
    2,408

    So after a little bit or research I find out that...

    So after a little bit or research I find out that the place that had this machine had special firmware installed. (who knew you could even do this!) This allows them to connect the machine to their...
Results 1 to 25 of 313
Page 1 of 13 1 2 3 4