Search:

Type: Posts; User: Solotime

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    0
    Views
    667

    Konica Minolta C220 parts available

    I have a clean running C220 with about 180K. Going to part it out so let me know if anyone needs anything.
    Thanks!
  2. Replies
    13
    Views
    4,032

    Re: Bizhub 222 stuck in abort loop

    Because the Total Clear function is available from the trouble reset screen.
  3. Replies
    13
    Views
    4,032

    Re: Bizhub 222 stuck in abort loop

    Got back into it by doing a total clear
  4. Replies
    13
    Views
    4,032

    Re: Bizhub 222 stuck in abort loop

    None of the suggestions will work. If there is no way to get into the service mode other than using the utility/counter button method then I may just have to replace the machine
  5. Replies
    13
    Views
    4,032

    Re: Bizhub 222 stuck in abort loop

    9272 does not work. I can get to the cold or trouble reset screen. Need to get back to service mode
  6. Replies
    13
    Views
    4,032

    Re: Bizhub 222 stuck in abort loop

    Thanks for the replay but that is not the issue here. Machine was working fine. I was in the service mode and set the hard drive to installed when it has no drive. As soon as I turned the machine off...
  7. Replies
    13
    Views
    4,032

    Bizhub 222 stuck in abort loop

    Checking on a slow printing issue for a customer and I inadvertantly set the Hard Disk to Installed. Now the machine keeps aborting. Can not get back into service mode to turn the HD back off unless...
  8. Re: Bizhub 361 scans mostly black from glass and lines from ADF

    Got it fixed. I had to adjust the rear of the second mirror assembly. With the glass off and looking down into the first mirror I could see that the second mirror was not level. I just lifted up the...
  9. Re: Bizhub 361 scans mostly black from glass and lines from ADF

    By reforming I am guessing they used the factory jigs to realign it...which I do not have unfortunately. Hopefully someone else might have seen this need to re-align the optics after a move and chime...
  10. Re: Bizhub 361 scans mostly black from glass and lines from ADF

    Yes, it was just moved across town to a new office. When you say trouble with the optics..anything specific I can look for? I did look at the mirrors to make sure they were all seated properly.
  11. Bizhub 361 scans mostly black from glass and lines from ADF

    Hello All,
    I am working on a Bizhub 361 that has an issue I have seen once before but never got to fix.
    It is a scanning issue in that the internal prints and PC Prints are fine but anything that...
  12. Replies
    9
    Views
    1,138

    Re: Garbled print on Bizhub 222

    So far the machine has been fine since "uninstalling" the HDD in the service mode. Only been 4 or 5 days but so far so good.
  13. Replies
    9
    Views
    1,138

    Re: Garbled print on Bizhub 222

    I was not in the service mode and it did not give me the option. I am thinking hard disk errors. I was simply going into the Admin Area and the screen came up saying due to a recent change (I made...
  14. Replies
    9
    Views
    1,138

    Re: Garbled print on Bizhub 222

    I tried this late yesterday. After that, when I went into the admin mode it immediately tells me to format the HDD. So I started the format process and it did nothing for 2 hours. So I shut it down,...
  15. Replies
    9
    Views
    1,138

    Garbled print on Bizhub 222

    Anyone seen this issue?
  16. Replies
    1
    Views
    545

    Bizhub 552 Lower Right Door Claw

    Need a part number for the Latch or claw as Minolta calls it. The front one on the lower right side door just below the Bypass Tray. Need the number for the B&W 552 NOT the C series.
    Thanks!
  17. Replies
    11
    Views
    1,243

    Re: C253 Operational Question

    They are printing from Word and Publisher. Both programs do the same thing. Looking into the offset each job setting....
  18. Replies
    11
    Views
    1,243

    Re: C253 Operational Question

    Not sure on the firmware level but their C552 with a booklet finisher does the same thing....
  19. Replies
    11
    Views
    1,243

    Re: C253 Operational Question

    [QUOTE=copytechman;463154]If you've installed the correct driver there should be an offset checkbox under the basic tab. it may not be checked by default.

    Regards!

    Yes that box is checked....
  20. Replies
    11
    Views
    1,243

    C253 Operational Question

    On a service call yesterday and the customer asked me why their C253 with 519 Finisher will not offset stack when printing from the computer. It seems to work on single sided but does not offset...
  21. Re: HP M551 Blank Display and Heartbeat LED Flashes twice

    Update: The SSD is what is causing the no display/blank display. Once I removed it and reboot I get my display back. I then installed the firmware and it completed ok but when rebooting it comes back...
  22. HP M551 Blank Display and Heartbeat LED Flashes twice

    Customer brought in this printer in for service suspecting a lightning strike. Printer would boot up saying checking disk and get to around 38% before eventually throwing a 98.00.0C error. As per the...
  23. Replies
    9
    Views
    7,190

    Re: M4345 Hangs on boot up

    Thanks Faxman, this is exactly what the printer is doing. FN104 is NOT rotating but everything else is the same. No engine test print, Dark Display etc.
  24. Replies
    9
    Views
    7,190

    Re: M4345 Hangs on boot up

    Also the boot progress is at 6/6 and ABCDE are in black blocks and F is not.
  25. Replies
    9
    Views
    7,190

    Re: M4345 Hangs on boot up

    I have the machine in my shop now and have removed the front covers and have access to FN101. It is not turning and there is less than 1 volt measured at the connector so this would seem to indicate...
Results 1 to 25 of 223
Page 1 of 9 1 2 3 4