Anybody know the answer to this? MF733cdw error code E021-1000
Thanks in advance!!
Type: Posts; User: t85ster
Anybody know the answer to this? MF733cdw error code E021-1000
Thanks in advance!!
scanmc, we don't have a spare anything, for this series. I am now suspecting that the yellow LED array is either defective, or out of adjustment laterally front to rear. Do you know if it is...
Yellow color offset front to rear of approximately 1mm. Is there an adjustment for this?
Thanks!
We are a Konica dealer, but we have this C5250 with a bad HDD. Before ordering a new HDD and tackling it, we wanted to see if we could get the necessary Firmware for this machine. We do have the...
Extremely damp paper will cause this type of problem. First pass thru is washed out, second pass thru is good because paper dried out during the fusing process during the first pass.
I'm trying to get a heads up from you guys before I go to this machine in the morning, I'm mainly a Konica tech. Thanks in advance for any suggestions!
[QUOTE=mascan42;1575205]Just to clarify, the copier isn't on a UPS. It's on the standard power filter that we sell with every machine. I swapped it out with another one, just so I could test the one...
Never plug copiers into the Battery Backup outlets on a UPS. Only use the "Surge Protection Only" outlet. The internal battery can't properly supply the current load of a copier or laser printer. My...
Are your guys trained/experienced on the Bizhubs?
1. Remove the Transfer Belt Unit and clean the two color registration sensors properly.
2. Make sure to use only OEM Toner!
These suggestions may seem silly and redundant, but your problem just might be caused by one of the following. I've seen it many times, and applies to all fax machines. This is the order that I...
CLJ Pro M277dw. When it starts to feed paper, it makes a loud pop noise, the cassette lift plate does not lift, feed rollers are not turning. This is an intermittent problem.
I returned yesterday to the machine. The customer gave me some more accurate history of when the issue started: The machine said it was out of Yellow toner. She replaced it, and that's when the...
Another tidbit of info I found out. The customer saved the old toner cartridge (they are all OEM, btw), and it was still about 1/2 full. So, the problem started out of the blue, before it actually...
Well guys, I tried all of your suggestions yesterday, to no avail. Today I will revisit the machine, and try a Auto Toner Sensor (K) Calibration, just for grins. The machine has only about 65k on it,...
eStudio 3540C not recognizing new toner cartridge
Have not arrived onsite yet, wanted to get a heads up before driving 40 miles there, then fumbling around. I'm a Konica Minolta tech, 43 years....
I'm trying to get a heads up on this problem before I arrive onsite. Not very familiar with Canon calibration and test procedures. Thanks!
You're a lot braver than me, copyman!!! :eek: If we never hear from you again after the service call there, who should we contact? RIP brother...
[QUOTE=copyman;700166]Ha-ha I know i can't believe it either. An "old" customer called who I haven't heard from in at least 5 years. This normally would of been an account I would have called to...
Thank you for checking. I look forward to your update!
Thanks for the good idea, mikadonovan! They don't have it in stock though. :(
I need a good working DF-3040 for the Lanier LD645C/Ricoh/Savin equivalent. My Customer's RADF got mangled in moving (their fault!). Thank you!
Thanks for checking!
My customer mangled their DF-3040 moving their Lanier LD-645C themselves with a pickup truck, so we thought if we could find one cheap enough somewhere, we wouldn't have to scrap the whole machine....
My customer mangled their DF-3040 moving their Lanier LD-645C themselves with a pickup truck, so we thought if we could find one cheap enough somewhere, we wouldn't have to scrap the whole machine....
Getting error 061-395. Checked and cleaned all drum crums, swapped drums, same problem. Can’t reset. Any clues appreciated!