Hi Seniors,
It's a SP9100 printer .when client send print command and stays at please wait and after sometime it throws SC990.
I have replaced the hard-disk .Swaped memory module and motherboard...
Type: Posts; User: muaazgujjar
Hi Seniors,
It's a SP9100 printer .when client send print command and stays at please wait and after sometime it throws SC990.
I have replaced the hard-disk .Swaped memory module and motherboard...
Actually I was planning to upgrade some MFPs with 115V power supply units to 220V and I have arranged some power supply units and heater units of 220V .But the choke coils in those PSU are missing...
Hi,
Is it possible to swap CHOKE COILS of PSU (220V) MFPs of different series and models of B&W and Colored?
I am talking about CNL almost in all P2P diagrams in PSU area.
HI everyone,
I am very grateful to all of you. and specially "ZED 255".
There was a missing connector with"SDVDB" ._CN 921_
It is 2 pin connector on left upper side of board and there is another...
Hi,
These are two MP 2852/3052 with with SC 995-01.It's very new to me. I need guidance.I have tried SSP mode to enter serial # etc but could not clear the SC.
Thank you sir,
I am planning to swap PSU as per your guidance an din case of no success I will try another controller board .
Any other valuable advice by other seniors please !!
Firstly,Thanking you all for valuable advices.
I have re-plugged all the connectors of PSU & BCU and the position changed as given below:
1.replaced DIMMs and tried .There was SC 672 displayed....
Hi,
I have double checked all fuses and connectors at PSU and start the unit.
Now the unit starts and stay at "Please wait " for a minute or so and then machine restarts and SC 819( 5344...
AN ANGEL arranged the firmware for me.
May God bless him.
However I am grateful to others too.:rolleyes:
Hi Seniors,
It is an AFICIO MP C2551 with SC 819.
The scenario is below step wise:
1.Machine's power supply burnt due to surge and 2 varistors and 02 fuses were exploded.
2.I repaired the...
Hi seniors,
I desperately need AFICIO MP c 2551 firmwares.
If anyone can help me.
I am trying to update the firmware of an AFICIO MP4000 but it do not accept the SDCARD ,whereas the same SDCARD works fine in another unit. BTW SC 819 displayed.Is there any possibility to access the...
It is MP5000 B
Thanking you for the reply.It is the which I want to tell.But the stud and Flap with transparent plastic blade are intact and in the Hopper assembly.
Presently the piece is not in front of me .I...
1st of all,Sorry for miss presentation as English is not my Native language.
I have double checked CPDU of this machine ,weighed the developer in the tank and deeply examined the mesh with mixing...
Thanking you Totoro & Kanuki2 for the prompt replies and sorry to miss some details in my last posts.
Toner bottle is MP4500A and gears are physically checked for breakage and found ok.
It's an AFICIO MP4000 always alarming "Toner Bottle is Almost empty ,Replace Toner Bottle" after some copies/prints.
The detailed issue is:
My client fixed the toner bottle and machine started...
Thanking you all for the prompt reply but I am still confused about this .would you please give me some tip/reference from service manual/user manuals page number etc.
Dear Seniors,
A few units in the lot of MP4000 are with the settings "Duplex on by default" and user have to use the touch panel every time to copy 1 side to 1 side .By default units are set to...
Happy new year,One of my clients upgraded his personal computer with "win7" plateform and attached it with AFICIO 2022 .He tried to scanbut his scanning software stopped working ( ADOBE ACROBAT...
Just replaced transfer belt cleaning blade two days back.
Hello!
I am trying to fix an AFICIO1045 with SC304. appearantly transfer section and transfer belt assembly etc are OK. Cleaned ID sensor but the problem is there.
Any guidance by he seniors...
Hello!
It's an Aficio 2027 (copier only) equiped with a harddisk 10GB .When my client tries to make multi copies ,the unit shows memory full after 20 to 25 originals got scanned.The client is...
yes It has 256MB and other items already attached with but the problem is still there.
Yeh