Every toner i install does few copies
Before installing another new toner, remove the toner dispensing unit. Remove the toner bottle motor. Clean the motor shaft. Remove coupling that was on the...
Type: Posts; User: Mukasa
Every toner i install does few copies
Before installing another new toner, remove the toner dispensing unit. Remove the toner bottle motor. Clean the motor shaft. Remove coupling that was on the...
hello Apkareno ,
all the fuser components are good , when i cable socket for the fuser i measured 220 volts mains but putting the fuser cable in its socket the 220 VOLTS disappears and it measures...
i checked the Fuser lamps ,the thermostats with a digtal meter they were all ok .
For the Thermistor at least the fuser has to warm up a bit , but the fuser is very cold.
Godfrey
Thanks, i managed to reset the fuser and HDD format but still the error C6000 come back.
I suspect the Power supply now what do you suspect to be the problem.
Godfrey
Hi Guys ,
I can't go to service mode after replacing the HDD , how can i reset this error C6000 , i checked the fuser is fine.
Godfrey
Hi I have a kyocera machine 520i with faints copies , but when you power toner direct to tank is makes good copies. what might be the like cause. mukasa
where is your email address?
Hi
yes you can reset by replacing new drum Crum Chip and Fuser Crum Chip.
Guys
I have a Xerox Epson 9400 wide format color plotter, when powered it tries to initialize but ends up displaying 00010014 error.
I have replaced the Pump assy the fault is still coming
what...
I have a Xerox Epson 9400 , when powered it tries to initialize but ends up displaying 00010014 error.
i have replaced the Pump assy the fault is still coming
what can i do to rectify this error.
Hi
Do you have the CDs which came with the machine
Hi my friend
What is your email address i send you some literature to read.
hello ,
Happy prosperous new year all.
I have used all the 4 Sequence power boot mode , changed the memory the fault is still coming.
This fault code 116-399 i has been on and off using the...
Thanks bro,
the cables are fine because after installing the software the machine connects and start printing normally , but after three to five days it looses the connectivity . what i do is to...
Hi
Xerox 260 fiery bustled bustled is very stubborn it works for two days then it fails to connect , it looses network .
For the last one month i have installed software four (4) times. I have...
Hello Zaza ,
When does this code come on , when warming up or when you press start to print.
These fault code is about the ROS Motor.
The ROS Motor rotation speed does not reach the ...
Hi
Can try this if it can help
The IBT Home Sensor does not detect the Belt Home signal.
NOTE:
If this fault is declared 3 times in succession, print mode will be disabled. In order to...
Magenta Dispense failure.
M Dispense Status NVM 762-369
0: Dispense Ready
1: Dispense Doubt
2: Dispense Near Broken
also think of the toner sensor in the Dev box
Hi every one , my color xerox 7435 black toner only print 3500 copies the displays add toner but when you check toner bottle toner is still there , this is the fourth time doing it .
its now very...
Hello Friends ,
I have a Desktop Canon iR 2520 which failed feeding papers in the tray 1 using landscape i only feed it portrait , but now it has even failed two sided coping and printing
it jams...
[QUOTE=Gh-jim;605138]Hello, I have a problem, the page 13.240.20.38 does not appear, I have a Xerox 6204 with external unit, a year ago and after a drop in voltage, the controller is HS and I had...
Hay Brother lets go slow,
lets go step by step
do you have the Os recovery/install cd
Yes or No
help me out ,when ever i install new software it works for a week then starts to misbehave .
i install all the three CDs , how can i make it work for along time.
Muks
thankx
am tech for xerox
but this machine is working now
thanks