Search:

Type: Posts; User: gliderider

Page 1 of 6 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    18
    Views
    2,362

    Re: e-studio 281c

    The 3511/4511 series was my first foray into the world of Toshiba color copiers. It's a wonder I didn't pull all my hair out. I remember going around to al the ones we had in the field and replacing...
  2. Replies
    6
    Views
    1,044

    Re: Toshiba E-256 Paper jamming.

    The only other thing I can add to Blackcats post is this. You didn't describe the type of and location of the jam. This wouldn't happen to be accordion jamming? if so, then your drive pin in the...
  3. Replies
    2
    Views
    679

    Re: Toshiba parts

    Hi:

    Check out PrecisionRoller.com: Online Shopping for Toner Cartridges & more I believe they have the parts you need.
  4. Replies
    4
    Views
    913

    Re: Toshiba estudio 2508A

    Power up by holding down the home and start key.
  5. Replies
    15
    Views
    3,182

    Re: e-studio 2508a

    We tried replacing the memory early in the troubleshooting process but to no avail. Also replaced the power supply which also made no difference. I do not know if the front office ever tried getting...
  6. Replies
    15
    Views
    3,182

    Re: e-studio 2508a

    Had the same issue and same symptoms on that model last year. I tried numerous things without success. Called Toshiba tech support and they had us replacing the sys board. Appeared to work but within...
  7. Replies
    6
    Views
    1,097

    Re: 6560c ADD TONER CONDITION FOR BLACK

    I would slide out the epu tray and check for toner in the sub hopper since the toner cartridge has to feed that first. If there is toner in the sub hopper than slide the door open on the bottom of it...
  8. Replies
    4
    Views
    675

    Re: e2000AC MR3031

    Yes. You can peel back the label on the fan which exposes the bushing and lube that.
  9. Replies
    4
    Views
    675

    Re: e2000AC MR3031

    First I would check to see if you are having the same issue off the glass. If not, double check your paper tray guides then in 05 mode 3043 decrease the indicated value for more gap.
  10. Replies
    5
    Views
    2,820

    Re: toshiba e studio 6508a error code f090

    So are you saying that you followed the procedure exactly as it is spelled out is the service manual?
  11. Replies
    6
    Views
    988

    Re: e2555c Developer Swap

    If memory serves me the 3555 and 4555 were the high speed units. you can not run a high speed developer unit in the 2555 without changing the front cover,( the one that couples the dev and epu...
  12. Thread: 5560 CE40

    by gliderider
    Replies
    12
    Views
    2,141

    Re: 5560 CE40

    I would go after the transfer belt first. Those were know for issues with the rear transfer roller blocks separating which would lead to a lack of transfer. There was a bulletin regarding this. You...
  13. Replies
    4
    Views
    791

    Re: 2550c light copies black

    Sounds like you are just papering over an underlying problem. You made no mention of where the copier is at in its pm schedule. Are you at or over pm and/or drive counts for this copier? Did you...
  14. Re: Oki CX3535T / Toshiba E studio 3540c CA00 Error Code

    As a humble Toshiba field service tech I would just cut right to the chase. I would power down and then power back up. Let the copier code out. Remove the transfer belt and look at the calibration...
  15. Re: Can I re-format Toshiba hard drives for a different model?

    If you have access to Toshiba's FYI tech site then search Copier Bulletin GEN-178 REV. 08 Hard Drive Part numbers per each model. Great reference. According to the part numbers the 407CS series uses...
  16. Replies
    9
    Views
    1,277

    Re: Toshiba 456 tray 1 and 2 jams

    Cold you provide a little more information like total copy count and error codes. Since most of this generation of copiers is getting up there in age I would be thinking of updating reg assy with new...
  17. Re: eStudio 2540c Black Toner Not Recognised

    Start by removing the inner cover where the copies land. Remove all the toner carts. You will see each individual toner cart drive and assy that have to be cleaned so they recognize the toner carts....
  18. [Misc] Re: Toshiba E-Studio 305se Looking for a part number

    Guide-exit-upr-l-473
    6LH54079000
  19. [Misc] Re: Toshiba E-Studio 305se Looking for a part number

    Are you referring to the piece that the duplex gate attaches to?
  20. Re: Toshiba e255SE - LCD panel has Lime Green display

    Have seen that before. Had to replace the entire touch screen to resolve it.
  21. Replies
    1
    Views
    655

    Re: e-studio 2050c close door

    You could still be having an issue with the rt side door not engaging the door switch. Also it couldn't hurt to clone the settings and then format and reinstall the latest firmware.
  22. Re: eStudio 3540C not recognizing new toner cartridge

    Remove the sensor, disassemble it and clean first before replacing it. Not that bad to get to. Remove all cartridges, remove inner cover. This exposes the toner drive shafts and toner cart sensor...
  23. Re: eStudio 3540C not recognizing new toner cartridge

    Those particular models are notorious for that. Check that the small chip on the back of the toner cartridge is still there and clean. That small toner chip interfaces with another small board behind...
  24. Replies
    6
    Views
    1,543

    Re: Parts for inventory?

    To be honest the new EBN copiers are requiring so few parts as compared to older models I don't keep anything in my car stock except for the normal adf/dsdf and tray feeds. Early on I was keeping...
  25. Replies
    12
    Views
    6,914

    Re: toshiba estudio 355 paper jam in exit

    That entire exit assembly had been updated continuously over the life of the copier. The color in the picture tells me it still has the original exit assy as the updated ones were black. One issue...
Results 1 to 25 of 132
Page 1 of 6 1 2 3 4