I did heat rollers on this unit about 5 months ago and unit has been running fine ever since. Then they called here yesterday with a C440 error code so I went here & reset the code. They called back...
Type: Posts; User: JDE75
I did heat rollers on this unit about 5 months ago and unit has been running fine ever since. Then they called here yesterday with a C440 error code so I went here & reset the code. They called back...
You need to replace toner roller nrolp1211 and the seals. Then you should be okay. What I have noticed is the toner roller goes bad, it's a spogy roller and once you replace it you should be fine.
We replaced the transfer roller and already checked the lsu. Only getting shading on trail and lead edges only when it's not being charged. Put in a new drum, ka1, dv, blade, fuser. Help!!!!
Thanks for the info but I have all of this and nothing is working. I replaced the drum, blade, developer and fuser unit and wires but still same problem. it's shading all over the pages and almost...
I need someone like now. 15 years is great experience.
Thanks for your help, the pad did work and the customer still hasn't calle dback in. Thanks again for all of your help.
Thanks for the suggestion. I did find that you don't have to clear all memory you can clear just tel/user data. It did work.
I can't find our manual for this unit but I do have for the CS1510 which they are very similar and it states that this code is a fixing unit error. Check all connectors to main pwb if all good then...
Did you check the white reference sheet??? I noticed once I replace that the e7-00 goes away.
I agree replace toner roller and seals and this will cure you're problem. The foam roller and seals go bad if that doesn't help then replace the hopper.
I was going to say I've had this problem with a few of these units and by doing the clutches and replacing the curl adj rollers seemed to fix the problem.
I have an AR235 that no matter what I do or replace the CQ is shading and double imaging. I have replaced the drum, drum blade, dv and fuser unit. I don't know if this is a bias problem or what. Any...
If you have a resume fax it to 630-887-7488. If not, what is your experience? What kind of copiers, faxes and/or printers have you worked on?
We are looking for a technician to fill a position immediately. We need techs for Toshiba, Samsung, Copystar, Kyocera, Sharp, Minolta which all know copiers are basically the same. Please contact me...
I need to delete all names and numbers and it doens't tell you how to in the service manual and I can't figure this out. Any help is appreciated!!!
Thanks in advance
Jamie
I have copies dark at the bottom shading even though drum and developer have been replaced. Already cleaned laser unit. Any suggestions????
Thanks in advance
Jamie
I have a customer that doesn't wnat the beeping noise when sending or receiving. I had them turn the ringer volume off and the speaker volume low but the beeping is still there and of course as a...
I have a customer that can't stand the beeping noise on transmissions whether receiving or sending. I had them turn the ringer volume off and the speaker volume to low but it still beeps. Now of...
You need to replace toner hopper and toner roller and then you'll be fine later on to reset code. Do you have part numbers and reset code? If not I can give you.
I have an Imagistics version of a Sharp and we can not get the nic card to rest even with the Sharp login. Any suggestions???? Thanks.
Tray #2 Keeps Reading Extra, Everything Is Set Right. Any Suggestions??????
Thanks but I already did all that. The lamps are fine, they do blink on and off, the thermostats are new and it clears but as soon as I go to make a copy the code comes right back on.
P * C * 14 Then 1 For Yes And Follow On Screen Directions, Code Should Clear Out.
Jamie
I KEEP GETTING AN H4-01 CODE. tHE LAMPS ARE FINE, THE PCU AND ICU ARE NEW AND PERFECT BUT I CAN'T CLEAR OUT THIS CODE. I AM ORDERING THE BOARD ON THE FUSER TO SEE IF IT'S THAT. DOES ANYONE HAVE ANY...