Search:

Would you all suggest I replace the DV unit, or just the DV?

No, drum is not covered in toner.

Drum is turning as is auger, DV unit turning. ITB is new, as is waste toner container. Toner is OEM. Meter is 174k, new customer so not sure of past history of machine. They stated the machine was...

Hi all,
First time seeing this model. Originally had a L4-12 error, ITB was bound up, replaced ITB and waste toner container. Machine then came up with replenishing toner and after a few went into...

I'll try to upload samples but background over ebtire page when it gets bad and drum and PCR are coated with toner and rotating the drum will not clean it off with cleaning blade, must wipe off toner...

Picked this unit up wholesale and it comes up with "enter account ID" screen. Can't seem to get into service mode either. Is there any way to get around this or get into service mode to do a HDD...

Compatible toner.

Hi all, have these two machines giving magenta background/repeating defects on copy and print jobs. Replaced magenta drums and dv units and problem still persists. 3050ci replaced ITB and machine...

Hi all,

Have this unit that worked fine for 2 weeks until it asked for a black printhead. Two PH later and it still won't recognize the black printhead.
Things noticed
When you open the access...

Customer has this unit, 94K, and a month ago the cyan toner read empty but it wasn't. Took chip off a new toner to see if it reset and it did. Now black is doing it. Can I get reset chips anywhere...

Reading 121 for over 5 minutes. Fuser powers up on start up, but once machine comes to ready, it never turns back on to keep temperature up, just goes into code.

Brian

Have this unit throwing c6050 error. Replaced fuser and still does it. Warms up, comes to ready but throws the code when trying to make a copy or in idle. Wall voltage good. Reseated all...

37262

I do have a picture of the op panel now, sorry for the delay, I was away and the school was closed for the summer. I don't know how to add the picture.
If someone can help me with adding a picture,...

Hi all,

I have posted about this unit before and with your help got it communicating and somewhat working. Mechanically it works well. Customer complains that it is slow to process jobs, errors...

Hi all,

Replaced the ink supply station on this unit due to leaky cartridge and now just throws error code on display. I know that on the larger units there is a sync between supply station and...

Hi all,

Customer has this unit thowing many SC796 and Jam code 248 and 996. I know it points to the finisher. I've cleaned all sensors, Checked motor, solenoid and switch operations in the front...

Thanx again Kiran, I have the JetDirect programmed and communicating but can't find a 64 bit driver that works for it. Any help would be greatly appreciated.

Brian

Thanx Kiran, but the link sends me to an out of date page, same as most of the links I have tried

Brian

Hi all, customer got this machine free, needs belt, but trying to get it to communicate first before investing in it. How do I program the JetDirect card with IP address and all?
Any and all input...

Have a customer who got this unit and it needs a belt, but first I need to know if a driver is still available. Customer is running Windows 7 and I assume an XP driver would work, but can't find one....

Hi all,

Customer has an Imagistics IM3511 that crosses to a Sharp ARM355/455. Question is, is the sharp DV unit directly compatible with the Imagistics? Part # for the DV unit for Sharp that I...

Customer has this machine that will not ptint. Comes to ready and either a print job sent or status page from the control panel will not ptint. Machine fires up, fans and motors turn, job shows in...

A few more things, this KM was never installed on this computer, and this PC is not part of the network.

I dl the KM software but since Windows never sees the KM, the KM software finds nothing to...

Just installed this unit to a customer that just updated to Windows 10 and Windows won't connect thru the USB port, doesn't see the KM. I swapped interface and main board but to no avail.
Anyone...