Search:

Type: Posts; User: ebm

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    2,878

    You could start with replacing/checking the...

    You could start with replacing/checking the decurler roller. J32-02 is indicating a jam by the reversal sensor. However, I ended up swapping the whole machine out the last time I had this jam code....
  2. Replies
    3
    Views
    2,103

    Been having problems lately with the Bizhub color...

    Been having problems lately with the Bizhub color machine paper trays not seating properly. This causes tray lift errors or no feed errors from the trays. Try watching as the paper lifts and...
  3. Replies
    7
    Views
    1,576

    You didn't mention if you tried adjusting the...

    You didn't mention if you tried adjusting the display density dial above the "Accessiblility" key or if you verified the operation panel is mounted correctly and the cable is installed correctly...
  4. Replies
    6
    Views
    1,354

    How about the torque limiter for the lower DFP...

    How about the torque limiter for the lower DFP roller? I have had to replace the entire PF unit because I could not figure what was causing the jams even after replacing rollers,clutches,torque...
  5. Thread: konica1212

    by ebm
    Replies
    1
    Views
    562

    Can't remember the last time I worked this model....

    Can't remember the last time I worked this model. But, if the F28 is the t/s corona error you can try removing the separator wire and see if it works. If it does, you can try cleaning the posts if...
  6. Replies
    5
    Views
    1,131

    have yu cleaned the optical mirrors? dusty or...

    have yu cleaned the optical mirrors? dusty or hazy mirrors can cause image scanning problems.
  7. Replies
    1
    Views
    1,141

    [Jamming] Does the machine say add paper to tray 1 if it is...

    Does the machine say add paper to tray 1 if it is empty? Does this only happen during multiple copying? What happens if you have one sheet in the tray and make one copy? I am wondering if the...
  8. Thread: 4101 error code

    by ebm
    Replies
    1
    Views
    2,075

    Looks like the PMDB is connected to the PRCB. If...

    Looks like the PMDB is connected to the PRCB. If you have eliminated the write unit and power supply, this might be the next step. The write unit is also connected to the OACB.
  9. [CQ] You seem to have isolated the problem to the ADF....

    You seem to have isolated the problem to the ADF. I wonder, does the shadow come out cyanish in black or single color copies also? If so, what could cause it to come out that color? Just something...
  10. Replies
    4
    Views
    3,239

    Description N-33 error when scanning to SMB....

    Description

    N-33 error when scanning to SMB. The shared folder is on the domain server and the user account has full control of the folder.

    Solution

    CAUSE: Scanning SMB to a shared folder of...
  11. Replies
    5
    Views
    1,916

    Can you post a sample image of the defect? Does...

    Can you post a sample image of the defect? Does the drum show any wear marks after the 1 week? When you remove the drum from the dv unit, is the dv level across the mag roller? Sometimes the...
  12. Replies
    5
    Views
    1,421

    Might be control board does not detect new...

    Might be control board does not detect new cartridge has been installed. How old is this printer? Is it still covered under warranty. KMBS printer guys are pretty good about replacing...
  13. Thread: KM4035

    by ebm
    Replies
    3
    Views
    1,091

    When in doubt, reload/update firmware.

    When in doubt, reload/update firmware.
  14. Replies
    6
    Views
    1,151

    [CQ] Is this a color copy/print or black? What...

    Is this a color copy/print or black? What happens if you run mono color copies -cyan,magenta,yellow,black?
  15. Replies
    6
    Views
    1,151

    [CQ] I would try replacing the magenta drum/image unit...

    I would try replacing the magenta drum/image unit based on the sample.
  16. Replies
    6
    Views
    1,151

    [CQ] Color registration adjustment doesn't help? TB 2...

    Color registration adjustment doesn't help? TB 2 addresses the color registration adjustment for this model. However, 2 inches is quite a shift. Is it possible to post a pdf sample of the problem?
  17. Replies
    3
    Views
    1,062

    Have you compared the setup between the two...

    Have you compared the setup between the two versions of acrobat reader for any differences that could cause this? Page scaling,auto rotate and center,choose paper source by PDF size,etc.?
  18. Replies
    3
    Views
    1,062

    Are the "arrow" points drawn to the edge of the...

    Are the "arrow" points drawn to the edge of the paper on the original document? If so, it looks like you have a magnification and/or centering problem. The shadows look like they are from the area...
  19. Replies
    8
    Views
    2,687

    I would say your transfer belt has "walked" or...

    I would say your transfer belt has "walked" or shifted to one side and this shifting would cause you to get 45-20 codes. The belt should be centered between the rollers and not over the collars too...
  20. Replies
    5
    Views
    1,421

    The cartridge(s) have a counter chip on them. ...

    The cartridge(s) have a counter chip on them. Have you checked the contacts in the machine where the blk toner sits?
  21. Replies
    5
    Views
    1,513

    [Error Code] Have you referrred to T.B. TAUS0646653EN...

    Have you referrred to T.B. TAUS0646653EN regarding thetransfer voltage arcing? Also, did you check PS17(fixing exit) and its wiring before or after you replaced the ADU board? I made the mistake of...
  22. Replies
    19
    Views
    4,303

    Adjust the "density" in the...

    Adjust the "density" in the Adjustment/Maintenance section of the System Menu. I have found increasing the density 1 or 2 steps darker makes a difference in the "solids" when making copies.
  23. Replies
    7
    Views
    3,625

    Konica came out with a new style holder to hold...

    Konica came out with a new style holder to hold the paper trays in. The new holders are black and you have to order a wire stopper ring with it. I use tie-wraps around the original white holders to...
  24. Replies
    4
    Views
    2,122

    I hope you are taking advantage of the Konica YPP...

    I hope you are taking advantage of the Konica YPP program. Might as well get a replacement fuser when you can since Konica is forcing the dealers to buy and replace their whole units. I hope Konica...
  25. Replies
    7
    Views
    1,340

    Sorry, Stirton M is correct. When color copying...

    Sorry, Stirton M is correct. When color copying (auto,full,mono color)only the color meter clicks. When black copying the black meter clicks. The default setting is still 2 clicks for 11x17 size.
Results 1 to 25 of 187
Page 1 of 8 1 2 3 4