In copy mode, Turn duplex OFF, then select program button, and program as default.
Type: Posts; User: StephenB
In copy mode, Turn duplex OFF, then select program button, and program as default.
Agree with Slim, if the paper empty does not light up, it's probably the sensor arm off it's holder or a bad sensor.
Other common issues with the 2550, make sure the white tray lift gear is not...
I would like to use a C2503 fuser in a C3003. The C2503 fuser does have the internal shutter just like the C3003.
However the C2503 has a different insert tab on the lower plastic cover of the...
I see that the C2003 fuser will work in the C3003 and C3503.
The Fixing film assembly for the C2003 is the same for the C2503.
The only difference I can see which prevents the C2503 fuser from...
Solved ! Turned out to be the ID sensor which is below the transfer roller. Wiped the sensor, which was coated with toner. ...
Thanks for all the suggestions, I did notice on the 5055 , SP 3-322-001 the adjusted Ifsg is way higher than the setting in 3-322-011 which indicates a dirty ID sensor.
I am returning today to the...
Picked up a Ricoh 5055 off lease to refurb. Print / copy density started off excellent. Has 270K total count. Quality started off excellent, did all firmware updates. All OEM toner, new OEM PCDU. Set...
I've seen this....something ( paper dust) or debris has gotten up in the cyan development section. Try separating the drum and dev units. You will notice a thin "void" on the mag roller.
Something...
I've found that if you replace Drum, Blade, Developer, charge roller ( all OEM) together, you'll have much better performance.
Also when your cleaning out the dev unit, check the "toner screen" at...
Regarding the 501 dreaded tray 1 lift issue....I have one out there where I added lift springs beneath the paper lift plate. So it gives the paper a "boost" when lifting.
The paper loads similar to...
Once you remove the ITB, the density sensor assembly will pivot freely, allowing you to clean it with a soft cloth.
A more common "gear issue" with these , and it sounds awful ...is a broken fuser drive gear
Almost for sure a door issue, the hole and zip tie fix works great. Happens all the time.
Do the repair, or the rear (right side) will break next, then the entire hinge.....and then you will need a...
make a copy, open door to stop the paper feed before it gets to the fuser.
If you have ghosting, problem is PCU related,
if no ghosting, problem is fuser.
Stick with OEM pcu's and toner. And...
Only when duplexing, I am getting frequent jams as the paper enters the inverter area. I believe the sensor going into the
inverter may be dirty or bad.
Is there a way to get to that sensor for...
Does it print OK thru the bypass - manual feed tray ?
Take the cover off the internal tray to expose the toner bottle. If it is NOT turning, I've seen where the toner feed mechanism spring is compressed away from the toner bottle. Press on it, it should...
If you can't get MS 365 working, change the smtp server set up to Gmail with 2 factor authentication or use smtp2go.
Make sure their MS 365 account is valid
( our ISP initially provided MS 365 at...
Great solution, Plug in your own wifi router and use your own I phone and try to Airprint.
You may want to check on the Web interface to confirm there is airprint available and make sure it's turned ON.
Also, I've had situations where the client is logged onto the "Guest" wireless,...
I've seen exactly what you're talking about.
There is a newer style of lower press roller bearings PN AE03-0053, which has a slight groove around the outside center which is held in place when the...
You did not say if you had tried the default login credentials, (lower case) admin , and no password ( blank).
Always easiest thru the web interface.
My apologies everyone....it turned out to be a bad Toner chip (pins) reader in the 401 itself. Replaced the assembly and everything is good.
Funny how this occurred right in the middle of a firmware...
I've had no issues with the Rfut, until now. But in an office, I change the IP address to prevent an accidental print. I also disconnect the fax line.
I'm updating my problem 401 now with an sd...
From another thread on a different machine in SP 7-931 Toner info being reset during a FW update can cause this.
On my problem 401, All the toner info settings are now 0h. On another working 401...