Search:

ok, thank you. I will have a look.

Thank you again for the info.

Thank you for the additional info. I will keep this and use it for next time.

Any advice on setting the Power saver mode time out? I want to set it for about 2 hours if possible.

Thanks,

I could not get the problem to come back. So for now I have to wait for it to fail again.

Thanks for the help.

I do now have another small issue. The customer is complaining about the...

Thank you I will try this on next call.

Appreciate your advice.

I have not run the sensor test. can you tell me which one it is?

I can try to run it on next call to check it.

But, like I said. it will clear and function for a while and then error out...

Sharp MX-M904 Error Code U6-63 Paper Tray Desk Trouble

I tried to reset this code several times. It allows me to reset it but then it comes back. It has to do with the Manual bypass try on top...

Ah, that makes sense. I did not have any formal training on this model. Just have the service documentation. Thanks for all the help.

;)

Thank you very much for the info. I went to the account today and ran 50-10 on HCT Bypass tray and the data setting was on 48. I had to move it to 95 and now its perfectly centered on 12 X 18 and...

No I have not tried sim 50-10. The high cap trays are centered so will this mess them up if I use sim 50 -10?

I can go back and give it a try.

They are running 80 pound card 12X18 and it...

Does anybody have an answer for this issue?

I need to center the image on 12 X 18 and all other paper sizes from the multi bypass tray. The bypass is Model MX-MF11 and sits on top of the high...

Ok I will give it a try.

I posted at the same time you did. Make sure we are talking about the same bypass model.

Thanks

All sizes. It does recognize 12 X 18 is loaded. I ran sim 40-2 but not sure if I did the correct sim. I have bypass tray Model MX-MF11. it sits on top of the high cap trays 5 and 6. Just wanted...

ok, so all the trays are feeding with the paper centered. The bypass tray is the problem. I can't seem to center the image. the bottom of the image is too close to the bottom of the sheet on 12 X...

How do you acquire a template for the media ?

I'm not sure how to do this. I am new on this machine model.

I am actually going over there now to see what I can do.

Any info. would be great....

I will be going over there on Friday. I will get back to you with more details. Basically they have a pre perforated sheet of about 20 tickets or so ( I will look at the sheet to make sure again)...

Hello again,

I have a customer that is trying to run perforated tickets on pre perforated paper. The image does not line up in the center of the perforated marks. They can shift it but then it...

I figured it out. One of the exit rollers was not snapped in all the way and it prevented the height sensor from not actuating. After snapping the white roller clip (oval shaped) back on the...

Grrrrrrr. I have another issue with the finisher. FN-22 finisher. the exit lift errors out. F0-03. Any clues.

I tried a sensor and it still just stutters when it initializes and gives the...

Great!!! Thank you both for the replies. I will try this next call.

Thanks again.

Ok, I finally got the machine all installed and it has been running good. I had some issues with the finisher but I got that resolved.

Now, I need to use the Raw copy tool and an SD card to...

Instead of fiddling around with the finisher, since it is a new install for the customer, I got another finisher with the same options. FN22 with Cutter, 3 hole, saddle fold and stitch. I removed...

ah ha, ok. I will get one delivered and try it out. I will keep you posted.

Thanks for all the help.

I replaced the sensor. I adjusted the solenoid for the entrance gate. Still jams. I found that the entrance plate on the saddle assembly was crooked a little bit. I loosened it up and re-mounted...

I upgraded to the latest firmware. I still get the same finisher jams in the saddle entrance. 2 to 3 sheets usually are jammed at the top transport entrance area. I ran about 40 books and it...

The finisher is used. I don't know exactly what you are asking but since its used there have been thousands of sheets through finisher. If you are just asking how many sheets make it when doing the...