Search:

Type: Posts; User: Canon.Tech

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    15
    Views
    6,012

    Re: BizHub C253 blank pages

    Start my stopping the machine mid run see if there is an image on the transfer belt & image units
  2. Replies
    4
    Views
    1,023

    Re: color setting

    Yes as said above, clean the optics then do a FULL auto gradation. However this model will NEVER produce what you would call a good quality colour copy or print even from new.
  3. Replies
    4
    Views
    1,023

    Re: color setting

    Yes as said above, clean the optics then do a FULL auto gradation. However this model will NEVER produce what you would call a good quality colour copy or print even from new,
  4. Replies
    6
    Views
    1,360

    Re: Developer Problem

    He is suggesting you replace the High Voltage Power Supply
  5. Replies
    19
    Views
    14,318

    [Misc] Re: Need Firmware Imaging Toolkit 2006

    Cheers, thanks for the info, so basically to be safe I needto store firmware for each machine on a separate SF card? But my question ishow can I tell what firmware I have, eg what machine is it for?...
  6. Replies
    19
    Views
    14,318

    [Misc] Re: Need Firmware Imaging Toolkit 2006

    Thanks for your reply. You’re right CF cards are cheap. But how do I know what firmware series is the same, EG is C451 the same as what? C550,C650!?
  7. Replies
    19
    Views
    14,318

    [Misc] Re: Need Firmware Imaging Toolkit 2006

    Can I have more that one machine model firmware on one card? or can I only keep one model on each card?
  8. Replies
    11
    Views
    1,479

    [Electrical] Re: image runner 2270 unresponsive

    Hi, you can have the drive for £50+ postage
  9. Re: MP C305SPF MESSAGE : Cartridges are not set correctly (Black only)

    I had a new install with a bent contact at the rear, bit of a strip down to replace the board, or you could simply reform the bent contact you do have to remove the board to do this however.
  10. Replies
    7
    Views
    1,647

    [Misc] Re: Which traing for new tech?

    The first thing I would do is send him out with one of your other engineers, get him to learn the basics first.
  11. Re: C1 imagepress Part number needed -developer drive gears

    My manual is the same.

    Looks like you'll have to order the complete dev drive ass'y
  12. Replies
    1
    Views
    549

    Re: Irc2550 rainbow lines

    Most likely one of, or all 3 colour drums, check the drum life % in service mode, & visually inspect the drums do they look worn? also if the rainbow lines are a zigzag Patten then you may need to...
  13. Replies
    6
    Views
    1,348

    Re: Canon ir1600

    What are the prints like? e.g do a windows driver test print page, or if it's a stand alone machine do a users list print out, what do these look like compared to a copy?
  14. Replies
    11
    Views
    1,479

    [Electrical] Re: image runner 2270 unresponsive

    You have the E0002 error because you have been turning themachine on/off without shutting it down correctly. Most likely you can reset this. The other fault you have is the HDD failing. I actually...
  15. Replies
    6
    Views
    881

    [Dead] Re: IRC2880i Dead

    Most likely the AC driver board is dead especially as you found a blown fuse.

    Before you replace it, It is worth removing all the cards and connections in the control box this is a common fault on...
  16. Replies
    2
    Views
    732

    Re: IR3300 no feed from drawers

    Does that stack feed work?
    If the machine shows paper in the draws then they are beinglifted OK so the deck has drive to it.
    Check it’s not simply paper trapper behind the cassettes,only takes a...
  17. Replies
    6
    Views
    1,348

    Re: Canon ir1600

    Light copies is most likely the dev unit on this old machine.

    Take it out have a look at the toner coverage, if the dev roller has white lines you will need to replace either the dev roller or the...
  18. Replies
    2
    Views
    642

    Re: Imageclass c8170 part

    This is the parts manual, look it up!

    http://cms.cmexonline.com.mx/media/canon/isgcatalogopartes/fichero/1076_mf8180c-pc.pdf
  19. Replies
    34
    Views
    6,676

    Re: Canon IRA C5051 Thermistors

    I'm blind too then!

    I have a good used film assy if you need it let me know
  20. Replies
    34
    Views
    6,676

    Re: Canon IRA C5051 Thermistors

    I'm guessing you have tried to reset the error?
  21. Replies
    10
    Views
    18,319

    [Error Code] Re: MPC 7501 SC899

    I needed this firmware myself & have just downloaded it, I've uploaded it for you, hope it is of use, it is the latest version on my Ricoh of the network, system/copy & engine.Post here when you have...
  22. Replies
    9
    Views
    1,802

    [Misc] Re: please help !! ricoh mpc 2050

    I agree, looks like you have a drum & developer fault.
    The black lines are caused by the drum & the other black marks are caused by the developer unit.
  23. Re: Konica minolta bizhub 600 Manual service (handbook).....

    or I've got that on my website free help yourself (see below)
  24. Replies
    4
    Views
    3,387

    Re: canon ir 1600

    When the drum fills with waste it pushes out a gear at the back & actuates a switch. Check this switch is not stuck in etc.
  25. Replies
    4
    Views
    3,387

    Re: canon ir 1600

    When the drum fills with waste it pushes out a gear at theback & actuates a switch. Check this switch is not stuck in etc.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4