Looks like a yellow banding issue?
Sent from my SM-G988B using Tapatalk
Type: Posts; User: HitMan
Looks like a yellow banding issue?
Sent from my SM-G988B using Tapatalk
Make sure the metal teeth on the PTR are not sticking out they tend to bend outwards over time. Push them back down/ in with a flatblade
Sent from my SM-G988B using Tapatalk
Try putting pressure on the right hand door when a prints goes through could be the PTR?
Also make sure the paper is not damp
Sent from my SM-G988B using Tapatalk
You might need to strip the fuser and clean the entrance blade.
Prints look a bit faded from the scanned image too could need new development unit
Or a good clean of the optics and a...
The hinges on the ardf are not the best- take off the rear adf panel and replace the screw with the spring on the closest hinge to the slit glass. Just put a normal screw in, I think it's the...
Try firmware but if that fails it's the controller
Sent from my SM-G988B using Tapatalk
https://www.copytechnet.com/forums/ricoh-savin-gestetner-lanier/152109-sc672-mpc3504.html
Sent from my SM-G988B using Tapatalk
It's a common issue on these devices. It could be the development unit.
You usually find the waste toner is one particular colour, the one that's causing the problem.
Sent from my SM-G930F...
I don't know where your located but that's one I've never seen before. Can only imagine it's from that time period. Lol I see your in the US just a bit far away to be getting that one [emoji23]
...
Please view this ad:
Photo Copier FREE to uplift,
Photo Copier FREE to uplift | in Musselburgh, East Lothian | Gumtree
Download the application from the Google Play Store.
Gumtree: Local...
I know you can swap the sensor with the little harness but you can also just swap the pins around on the little connector. On the c4502 drum unit if you have the connector with the little plastic...
Out of curiosity whats the salary like out that way roughly?
Sent from my SM-G930F using Tapatalk
I obtained this copier that has done 33k prints. There is a small scratch on the magenta drum but seems to be fine otherwise. Would any one be interested in getting this machine or parts from it? I'm...
It will probably need a strip down. I noticed when you pulled the finisher off the main frame that a sensor looks a bit squint. You might get away with pushing it in. Worth a shot. Just below the...
Ok
Sent from my SM-G930F using Tapatalk
Maybe I was in some sort of alternate universe when I done it before
Sent from my SM-G930F using Tapatalk
Alright then I'm talking shit
Sent from my SM-G930F using Tapatalk
Yeah you can strip out the parts and use them. The lube bar is about half the size of the higher speed machines as obviously they only last about 60k.
They are completely different part numbers and...
Apologies but I'm wrong about the c2503 fitting the c3503. The drum I'm sure is totally different. I was able to get the c2504 drum parts to fit in a c3503.
Sent from my SM-G930F using Tapatalk
You can swap the parts into the drum housing and it will work. Unsure of the dev unit though
Sent from my SM-G930F using Tapatalk
No the whole black unit with cylinder and cleaning parts fit
Sent from my SM-G930F using Tapatalk
The drums are the same and work, unsure of the dev unit but the same developer works in the original dev unit
Sent from my SM-G930F using Tapatalk
It should work but there might be a pin at the rear of the machine stopping the drum going in. If so remove the pin at the rear. Think this is only for 02's though
Sent from my SM-G930F using...
Could give it a try just make sure the rj45 connector at the rear of the drum is the same shape. Use a file if not. If the machine displays pcu not set the connector that plugs into the dev unit at...
It's the shaft that the drum sits into. Maybe get a file to it so the bearing can fit over it
Sent from my SM-G930F using Tapatalk