Search:

That is just to indicate the difference between the original and the copy that comes out. But even in A4 or Letter size that goes in sideways, the prints will be off by a few cm or inches on the...

Hi,

Lately the machine has been having issues with paper coming from Tray no. 2.

Sometimes the paper would just stop before reaching the registration rollers, sometimes it stops when the paper...

Thanks. I'll check those as well.

Thanks. I'll try to locate that sensor.

The Clutch work fine. The bypass feed roller spins and pulls the paper but the Lower Transport Roller does not.

Tried copying from the bypass tray to trigger the error. Then i printed the SMC report.

The most recent P Jam History entry is Code050 JamB FeedM

After that i tried making a duplex and the...

41432

Hi,

Lately the machine began having feed errors from the bypass tray. Turns out the paper stops at the roller as indicated by the included picture. The roller does not spin and pull the...

I am referring to the big box that is attached to the BICU board. The one with SDCARD slots and usb/network cards.

The service manual simply referred to it as MFP expansion component box.

I did...

Hi,

Our Aficio 2018D had retired and it had this expansion box that gave it network connectivity.

Can i use this expansion box on our MP2000 and hopefully give it print and network capability?...

The 5801 was the last resort and it was the first time i used it. I had managed to fix other problems before without it. I have a service manual and i consult it before making any moves.

This time...

Thanks for the reply.

Pardon me but is that equivalent to a factory reset? I have done a TD initialization before when I replaced the PCU but i haven't entered factory settings before. This is...

In our country, we are still able to buy replacement parts for our MP2000 and 2018D. Parts that often wear out such as development gears, transfer roller gears and the gear between the registration...

Thanks

Forgot to mention I also tried swapping an identical fusing unit from an MP2000 but still the errors persist.

The machine did not exhibit anything unusual before this happened. The first...

I was printing in my 2018D when I noticed that the copies coming out wasn't hot and the toner isn't baked into the paper.

I immediately stopped the printing and turned the machine off.

When I...

Recently, i noticed that developer powder is making it to the gears of the PCU of our MP2000.

This creates rough, grinding noises and worn out some of the gears.

What could be causing it?
...

Thanks for the tip. Yeah the unit's lamp is green.

So i managed to get the scan to email working by setting up a local mail server.

I tested it and the output was in grayscale (black and white)

Is the 2018D capable of colored scan outputs?
...

I tried the restricted gmail smtp: aspmx.l.google.com
39357

I get this error:
#[dcs_nas(19)]18/04/05 18:41:21 SMTPC: failed to connect smtp server. timeout. ERR:

Thanks. I'll give it a try. I configured the machine to send scans to my gmail account.

I forgot to mention i already assigned the router's IP as the primary DNS.

I'll give the restricted gmail smtp settings a try. Thanks a lot. I'll post an update later.

Here's the current setup:

The machine is connected to the network router via lan cable.

The machine is assigned a static IP, the gateway if the router's ip.

I can access the machine's...

Our machines use the same PCU and I did something like that but instead of using sealant, i used strips from a 3M dish washing foam. Works great. Does not cause bulging as the foam flattens when i...

Hi everyone,

Lately, i noticed frequent jams when using either Tray 3 or 4 on our 2018D. When i check the jammed paper, there are multiple sheets. I thought it was just the paper sticking...

Thanks for the inputs.

Here's what i did so far.

I removed the entire rear cover and used an identical one from a 2018d.

The problem still persists.

How can i check for the status of the...

One side prints just fine, but when the paper reaches the top portion and reverses back to have the other side printed, the paper just stops in its tracks. It's seems like the duplex motor is not...