Search:

Type: Posts; User: DH1980

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Thread: C4000 Exit Jam

    by DH1980
    Replies
    8
    Views
    519

    [Jamming] Re: C4000 Exit Jam

    I would try a different exit section. I have seen where the sensor can be covered in toner.
  2. Replies
    7
    Views
    1,275

    Re: PC600 color printer noise

    It was the ITB belt. A little white bushing is oblong and causing the noise. Had to purchase the whole unit to get the bushing.
  3. Replies
    7
    Views
    1,275

    Re: PC600 color printer noise

    The jam codes are 042. I did swap the ITB with a working machine. Hope that works.
    The noise is like gears not meshing. The noise comes and goes. I will report back after a few days.
    Thanks
  4. Replies
    7
    Views
    1,275

    PC600 color printer noise

    I have two PC600 making a bad noise then jam or cram the print. Sometimes it will throw the color registration off and sometimes it just crams the print to gether.
    I have been all over this machine...
  5. Replies
    4
    Views
    927

    Re: DD 3344 Out of ink

    Try running the pump by hand. If that works take the sensor with the prongs off of the drum and clean it.
    After that it could be board.
  6. Re: MP501 after running 100 copies it hesitates and is light or blank

    I think my trouble is in a board. Ricoh said to try board M2811064. Not a big fan of trying boards.
    My machine was not running low on toner because after it sits for a few minutes it is OK.
    Thanks
  7. Re: MP501 after running 100 copies it hesitates and is light or blank

    Tried new PCU and new developer with no luck. Still runs great for 100 or so then light or blank.
  8. Re: MP501 after running 100 copies it hesitates and is light or blank

    Thanks for the reply
    The product support guide shows 500K on PCU
  9. MP501 after running 100 copies it hesitates and is light or blank

    I have a MP501 that runs 100 prints or so then hesitates and runs light or blank prints. After it sets for a few minutes, it prints fine.
    Does this while coping from glass. Machines has 77k on it.
  10. Replies
    24
    Views
    3,693

    Re: Fast Moving Parts List

    Can I get a copy of the list
  11. Re: sp 4520dn jam just before exit only with main tray

    Agree check paper size and the back fence on the tray. I have seen them float back and cause add paper
  12. Replies
    14
    Views
    1,611

    [Misc] Re: Asking for advise: envelopes on Ricoh machines

    Had a Ricoh P 800 printer that would wrinkle envelopes no matter what setting I used. The envelopes were the standard com 10.
    Switched to the pre stick with tape and they worked perfectly. ...
  13. Replies
    24
    Views
    3,857

    Re: Mpc 2003 not able to load web browser

    I had a machine that would not load WIM and it was the antivirus software. Turned it off and it worked fine.
  14. Replies
    14
    Views
    8,803

    Re: MP 5055 won't detect new toner

    I agree with SP3701. I would trip each item in the PCU and make sure the machine runs like it is doing process control.
  15. Replies
    4
    Views
    2,187

    Re: Mp5055 drum/dev unit drive unit noise

    Have also seen waste bottle make noise. The machine sounds like a motor but it is the waste bottle.
  16. Replies
    5
    Views
    1,372

    Re: 8300dn WIM not accessible 404 service message

    Have seen firewall and anti spam give WIM some troubles on some networks
  17. Replies
    15
    Views
    1,966

    [CQ] Re: mpc 4502 pcu's crusty toner

    OEM = Original Equipment Manufacture
  18. Replies
    9
    Views
    2,121

    Re: Changing Bypass Tray Output MP 4055

    Could the bypass be set to thick paper?
  19. Replies
    9
    Views
    2,121

    Re: Changing Bypass Tray Output MP 4055

    I think output is based on copy, fax or print mode and not tray selection.
  20. Replies
    16
    Views
    44,735

    [Error Code] Re: MPC 3003 SC 672-11

    Sometimes the HDD can be the cause
  21. Replies
    174
    Views
    193,321

    Re: RICOH copeir monthly auto meter

    Hi
    Can I please get a copy brucembm@windstream.net
    Thanks
  22. Re: Ricoh Savin MP 6003 SC672-11 won't wake up from sleep mode

    Had a MP 7503 every morn go to functional reset trip code 991 992 customer had to unplug to reset.
    Updated firmware with package and changed SP5191 deep sleep mode to off
    It's been a week with no...
  23. Replies
    0
    Views
    1,705

    Best way to move MFP's

    What is everyone using to move MFP's in the 150 250 lbs. range?
    Thanks for any replies.
  24. Replies
    11
    Views
    6,424

    Re: Device Manager NX Lite

    I think you need the Device Manager Accounting to read the user codes.
  25. Thread: MY C3003

    by DH1980
    Replies
    12
    Views
    1,429

    Re: MY C3003

    We had an account that could not see WIM because of anti malware software. We disabled it and the WIM worked fine.
Results 1 to 25 of 46
Page 1 of 2 1 2