Turn on Batch print under Fax Reception Settings.
Type: Posts; User: kjg
Turn on Batch print under Fax Reception Settings.
Usually TR and/or Drum entrance guide. the one that comes in the maint kit.
There is also a top felt pad similar to the one in the toner hopper ( the one that can tear up and clog the hopper assembly). I have had them come loose and block the entry to the WTB assembly.
I...
I posted a while back on a 3655 in afternoon sunlight that would read WT full. I rotated the machine 90 degrees and problem went away. Then I just put a piece of cardboard next to the machine to...
Two things to check :
Its possible that the ID sensor came unplugged if the side door was ever removed. the plug is in the lower front of the machine. That would be the easiest fix.
Also, I have...
Lots of responses on this one.
I would agree to look at the clutch pack for feed. Replacement is not difficult. (was mentioned also - its a different number than higher speed models).
I own a 3540...
Is there a chance you could post a photograph if internal prints as opposed to scans?
With that being a scan its harder to give an opinion.
It looks too much like a DP scan position problem (from...
At least you made progress. The noise is the only thing that still concerns me. At any rate, it sounds like the vertical conveying unit will need to be pulled for further investigation.
Sounds like a stall in vertical conveying.
Take back cover off and rear left cover.
Get back and see if you can hear which shaft is causing that in vertical feed assembly.
I remember having a...
Function default may have been set for that mode.
I have customers who like quiet mode on their desk so it throws me off when it is so slow.
Might be a stupid answer - but, What are the chances it is set to quiet mode? that would slow it down considerably on all print/copy settings? Those may even have a quiet mode indicator light on the...
There is a black feed guide on the vertical conveying unit just below feed where unit 2 paper comes out that can have the tabs break off the edges. It is worth checking to see if they are missing. It...
That's a wide range of jamming issues.
I would revisit the drum input guide which comes in the kit and be sure it is not partly closed up on one side. I have had them pinched closed slightly out of...
Easy to get to:
System Menu/Counter, Adjustment/Maintenance, Silent Mode, On
With Silent Mode in On setting, the machine will not constantly cycle.
The only downside is that first copy out time...
These are very picky about power. Very picky.
We believe its a hot offset occurring when you see this. We have successfully corrected by changing settings in sim 161 back by just 5 degrees depending...
51800
Its been quite awhile since I have done one of these but here you go.
sorry for delay, I had a busy couple of weeks.
Parts Guide Transfer, 302GR94481. In parts manual page 11 Item A03. It comes in the maintenance kit. It sits just below the drum between the drum and the transfer roller and is held in with a single...
I find that series to be very picky to power. If you cannot find a resolution, try moving to another outlet. Be sure it is a clean outlet. Try it there and see if it clears up. Hope that helps.
Try changing both the transfer roller assembly and the drum input guide that comes in the maintenance kit. Both have caused me that grief in the past on multiple 420's and 520's.
One of these days I'll pull the DC-111 I still have off the shelf and clean it up. I still have toner, developer, feed rollers, cleaning blade, and a drum, and perhaps a heat and press roller. If I...
If you are using the turbo firmware, have you tried full firmware installation?
There is a rescue firmware available and installation from SD card as an alternative also.
worth a try at least.
Welcome!
It wouldn't happen to set where direct sunlight hits it at some point in the day would it? I installed one that wouldn't function at all until I moved it out of the light. I tested it to confirm it...
On the older 4200 we had this very problem with buildup on the press roller. Kyocera came up with a setting for letter paper type that helped. The following is from a firmware update :
Improvement...
Did this only happen after the MK was installed? If new MK was put in to correct, go and check the clear guide films that come in the kit. If they are installed too high they will interfere with the...